83 lines
2.0 KiB
Plaintext
83 lines
2.0 KiB
Plaintext
RT5650/RT5645 audio CODEC
|
|
|
|
This device supports I2C only.
|
|
|
|
Required properties:
|
|
|
|
- compatible : One of "realtek,rt5645" or "realtek,rt5650".
|
|
|
|
- reg : The I2C address of the device.
|
|
|
|
- interrupts : The CODEC's interrupt output.
|
|
|
|
- avdd-supply: Power supply for AVDD, providing 1.8V.
|
|
|
|
- cpvdd-supply: Power supply for CPVDD, providing 3.5V.
|
|
|
|
Optional properties:
|
|
|
|
- hp-detect-gpios:
|
|
a GPIO spec for the external headphone detect pin. If jd-mode = 0,
|
|
we will get the JD status by getting the value of hp-detect-gpios.
|
|
|
|
- cbj-sleeve-gpios:
|
|
a GPIO spec to control the external combo jack circuit to tie the sleeve/ring2
|
|
contacts to the ground or floating. It could avoid some electric noise from the
|
|
active speaker jacks.
|
|
|
|
- realtek,in2-differential
|
|
Boolean. Indicate MIC2 input are differential, rather than single-ended.
|
|
|
|
- realtek,dmic1-data-pin
|
|
0: dmic1 is not used
|
|
1: using IN2P pin as dmic1 data pin
|
|
2: using GPIO6 pin as dmic1 data pin
|
|
3: using GPIO10 pin as dmic1 data pin
|
|
4: using GPIO12 pin as dmic1 data pin
|
|
|
|
- realtek,dmic2-data-pin
|
|
0: dmic2 is not used
|
|
1: using IN2N pin as dmic2 data pin
|
|
2: using GPIO5 pin as dmic2 data pin
|
|
3: using GPIO11 pin as dmic2 data pin
|
|
|
|
-- realtek,jd-mode : The JD mode of rt5645/rt5650
|
|
0 : rt5645/rt5650 JD function is not used
|
|
1 : Mode-0 (VDD=3.3V), two port jack detection
|
|
2 : Mode-1 (VDD=3.3V), one port jack detection
|
|
3 : Mode-2 (VDD=1.8V), one port jack detection
|
|
|
|
Pins on the device (for linking into audio routes) for RT5645/RT5650:
|
|
|
|
* DMIC L1
|
|
* DMIC R1
|
|
* DMIC L2
|
|
* DMIC R2
|
|
* IN1P
|
|
* IN1N
|
|
* IN2P
|
|
* IN2N
|
|
* Haptic Generator
|
|
* HPOL
|
|
* HPOR
|
|
* LOUTL
|
|
* LOUTR
|
|
* PDM1L
|
|
* PDM1R
|
|
* SPOL
|
|
* SPOR
|
|
|
|
Example:
|
|
|
|
codec: rt5650@1a {
|
|
compatible = "realtek,rt5650";
|
|
reg = <0x1a>;
|
|
hp-detect-gpios = <&gpio 19 0>;
|
|
cbj-sleeve-gpios = <&gpio 20 0>;
|
|
interrupt-parent = <&gpio>;
|
|
interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
|
|
realtek,dmic-en = "true";
|
|
realtek,en-jd-func = "true";
|
|
realtek,jd-mode = <3>;
|
|
};
|