153 lines
5.0 KiB
YAML
153 lines
5.0 KiB
YAML
# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
|
|
%YAML 1.2
|
|
---
|
|
$id: http://devicetree.org/schemas/pinctrl/qcom,ipq6018-pinctrl.yaml#
|
|
$schema: http://devicetree.org/meta-schemas/core.yaml#
|
|
|
|
title: Qualcomm Technologies, Inc. IPQ6018 TLMM block
|
|
|
|
maintainers:
|
|
- Sricharan R <sricharan@codeaurora.org>
|
|
|
|
description: |
|
|
This binding describes the Top Level Mode Multiplexer block found in the
|
|
IPQ6018 platform.
|
|
|
|
properties:
|
|
compatible:
|
|
const: qcom,ipq6018-pinctrl
|
|
|
|
reg:
|
|
maxItems: 1
|
|
|
|
interrupts:
|
|
description: Specifies the TLMM summary IRQ
|
|
maxItems: 1
|
|
|
|
interrupt-controller: true
|
|
|
|
'#interrupt-cells':
|
|
description:
|
|
Specifies the PIN numbers and Flags, as defined in defined in
|
|
include/dt-bindings/interrupt-controller/irq.h
|
|
const: 2
|
|
|
|
gpio-controller: true
|
|
|
|
'#gpio-cells':
|
|
description: Specifying the pin number and flags, as defined in
|
|
include/dt-bindings/gpio/gpio.h
|
|
const: 2
|
|
|
|
gpio-ranges:
|
|
maxItems: 1
|
|
|
|
#PIN CONFIGURATION NODES
|
|
patternProperties:
|
|
'-pinmux$':
|
|
type: object
|
|
description:
|
|
Pinctrl node's client devices use subnodes for desired pin configuration.
|
|
Client device subnodes use below standard properties.
|
|
$ref: "/schemas/pinctrl/pincfg-node.yaml"
|
|
|
|
properties:
|
|
pins:
|
|
description:
|
|
List of gpio pins affected by the properties specified in this
|
|
subnode.
|
|
items:
|
|
oneOf:
|
|
- pattern: "^gpio([1-9]|[1-7][0-9]|80)$"
|
|
- enum: [ sdc1_clk, sdc1_cmd, sdc1_data, sdc2_clk, sdc2_cmd,
|
|
sdc2_data, qdsd_cmd, qdsd_data0, qdsd_data1, qdsd_data2,
|
|
qdsd_data3 ]
|
|
minItems: 1
|
|
maxItems: 4
|
|
|
|
function:
|
|
description:
|
|
Specify the alternative function to be configured for the specified
|
|
pins.
|
|
enum: [ adsp_ext, alsp_int, atest_bbrx0, atest_bbrx1, atest_char,
|
|
atest_char0, atest_char1, atest_char2, atest_char3, atest_combodac,
|
|
atest_gpsadc0, atest_gpsadc1, atest_tsens, atest_wlan0,
|
|
atest_wlan1, backlight_en, bimc_dte0, bimc_dte1, blsp1_i2c,
|
|
blsp2_i2c, blsp3_i2c, blsp4_i2c, blsp5_i2c, blsp6_i2c, blsp1_spi,
|
|
blsp1_spi_cs1, blsp1_spi_cs2, blsp1_spi_cs3, blsp2_spi,
|
|
blsp2_spi_cs1, blsp2_spi_cs2, blsp2_spi_cs3, blsp3_spi,
|
|
blsp3_spi_cs1, blsp3_spi_cs2, blsp3_spi_cs3, blsp4_spi, blsp5_spi,
|
|
blsp6_spi, blsp1_uart, blsp2_uart, blsp1_uim, blsp2_uim, cam1_rst,
|
|
cam1_standby, cam_mclk0, cam_mclk1, cci_async, cci_i2c, cci_timer0,
|
|
cci_timer1, cci_timer2, cdc_pdm0, codec_mad, dbg_out, display_5v,
|
|
dmic0_clk, dmic0_data, dsi_rst, ebi0_wrcdc, euro_us, ext_lpass,
|
|
flash_strobe, gcc_gp1_clk_a, gcc_gp1_clk_b, gcc_gp2_clk_a,
|
|
gcc_gp2_clk_b, gcc_gp3_clk_a, gcc_gp3_clk_b, gpio, gsm0_tx0,
|
|
gsm0_tx1, gsm1_tx0, gsm1_tx1, gyro_accl, kpsns0, kpsns1, kpsns2,
|
|
ldo_en, ldo_update, mag_int, mdp_vsync, modem_tsync, m_voc,
|
|
nav_pps, nav_tsync, pa_indicator, pbs0, pbs1, pbs2, pri_mi2s,
|
|
pri_mi2s_ws, prng_rosc, pwr_crypto_enabled_a, pwr_crypto_enabled_b,
|
|
pwr_modem_enabled_a, pwr_modem_enabled_b, pwr_nav_enabled_a,
|
|
pwr_nav_enabled_b, qdss_ctitrig_in_a0, qdss_ctitrig_in_a1,
|
|
qdss_ctitrig_in_b0, qdss_ctitrig_in_b1, qdss_ctitrig_out_a0,
|
|
qdss_ctitrig_out_a1, qdss_ctitrig_out_b0, qdss_ctitrig_out_b1,
|
|
qdss_traceclk_a, qdss_traceclk_b, qdss_tracectl_a, qdss_tracectl_b,
|
|
qdss_tracedata_a, qdss_tracedata_b, reset_n, sd_card, sd_write,
|
|
sec_mi2s, smb_int, ssbi_wtr0, ssbi_wtr1, uim1, uim2, uim3,
|
|
uim_batt, wcss_bt, wcss_fm, wcss_wlan, webcam1_rst ]
|
|
|
|
drive-strength:
|
|
enum: [2, 4, 6, 8, 10, 12, 14, 16]
|
|
default: 2
|
|
description:
|
|
Selects the drive strength for the specified pins, in mA.
|
|
|
|
bias-pull-down: true
|
|
|
|
bias-pull-up: true
|
|
|
|
bias-disable: true
|
|
|
|
output-high: true
|
|
|
|
output-low: true
|
|
|
|
required:
|
|
- pins
|
|
- function
|
|
|
|
additionalProperties: false
|
|
|
|
required:
|
|
- compatible
|
|
- reg
|
|
- interrupts
|
|
- interrupt-controller
|
|
- '#interrupt-cells'
|
|
- gpio-controller
|
|
- '#gpio-cells'
|
|
- gpio-ranges
|
|
|
|
additionalProperties: false
|
|
|
|
examples:
|
|
- |
|
|
#include <dt-bindings/interrupt-controller/arm-gic.h>
|
|
tlmm: pinctrl@1000000 {
|
|
compatible = "qcom,ipq6018-pinctrl";
|
|
reg = <0x01000000 0x300000>;
|
|
interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
|
|
interrupt-controller;
|
|
#interrupt-cells = <2>;
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
gpio-ranges = <&tlmm 0 80>;
|
|
|
|
serial3-pinmux {
|
|
pins = "gpio44", "gpio45";
|
|
function = "blsp2_uart";
|
|
drive-strength = <8>;
|
|
bias-pull-down;
|
|
};
|
|
};
|