162 lines
4.3 KiB
YAML
162 lines
4.3 KiB
YAML
# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
|
|
%YAML 1.2
|
|
---
|
|
$id: http://devicetree.org/schemas/pinctrl/microchip,sparx5-sgpio.yaml#
|
|
$schema: http://devicetree.org/meta-schemas/core.yaml#
|
|
|
|
title: Microsemi/Microchip Serial GPIO controller
|
|
|
|
maintainers:
|
|
- Lars Povlsen <lars.povlsen@microchip.com>
|
|
|
|
description: |
|
|
By using a serial interface, the SIO controller significantly extend
|
|
the number of available GPIOs with a minimum number of additional
|
|
pins on the device. The primary purpose of the SIO controllers is to
|
|
connect control signals from SFP modules and to act as an LED
|
|
controller.
|
|
|
|
properties:
|
|
$nodename:
|
|
pattern: "^gpio@[0-9a-f]+$"
|
|
|
|
compatible:
|
|
enum:
|
|
- microchip,sparx5-sgpio
|
|
- mscc,ocelot-sgpio
|
|
- mscc,luton-sgpio
|
|
|
|
"#address-cells":
|
|
const: 1
|
|
|
|
"#size-cells":
|
|
const: 0
|
|
|
|
reg:
|
|
maxItems: 1
|
|
|
|
clocks:
|
|
maxItems: 1
|
|
|
|
microchip,sgpio-port-ranges:
|
|
description: This is a sequence of tuples, defining intervals of
|
|
enabled ports in the serial input stream. The enabled ports must
|
|
match the hardware configuration in order for signals to be
|
|
properly written/read to/from the controller holding
|
|
registers. Being tuples, then number of arguments must be
|
|
even. The tuples mast be ordered (low, high) and are
|
|
inclusive.
|
|
$ref: /schemas/types.yaml#/definitions/uint32-matrix
|
|
items:
|
|
items:
|
|
- description: |
|
|
"low" indicates start bit number of range
|
|
minimum: 0
|
|
maximum: 31
|
|
- description: |
|
|
"high" indicates end bit number of range
|
|
minimum: 0
|
|
maximum: 31
|
|
minItems: 1
|
|
maxItems: 32
|
|
|
|
bus-frequency:
|
|
description: The sgpio controller frequency (Hz). This dictates
|
|
the serial bitstream speed, which again affects the latency in
|
|
getting control signals back and forth between external shift
|
|
registers. The speed must be no larger than half the system
|
|
clock, and larger than zero.
|
|
default: 12500000
|
|
|
|
patternProperties:
|
|
"^gpio@[0-1]$":
|
|
type: object
|
|
properties:
|
|
compatible:
|
|
const: microchip,sparx5-sgpio-bank
|
|
|
|
reg:
|
|
description: |
|
|
The GPIO bank number. "0" is designates the input pin bank,
|
|
"1" the output bank.
|
|
maxItems: 1
|
|
|
|
gpio-controller: true
|
|
|
|
'#gpio-cells':
|
|
description: |
|
|
Specifies the pin (port and bit) and flags. Note that the
|
|
SGIO pin is defined by *2* numbers, a port number between 0
|
|
and 31, and a bit index, 0 to 3. The maximum bit number is
|
|
controlled indirectly by the "ngpios" property: (ngpios/32).
|
|
const: 3
|
|
|
|
interrupts:
|
|
description: Specifies the sgpio IRQ (in parent controller)
|
|
maxItems: 1
|
|
|
|
interrupt-controller: true
|
|
|
|
'#interrupt-cells':
|
|
description:
|
|
Specifies the pin (port and bit) and flags, as defined in
|
|
defined in include/dt-bindings/interrupt-controller/irq.h
|
|
const: 3
|
|
|
|
ngpios:
|
|
description: The numbers of GPIO's exposed. This must be a
|
|
multiple of 32.
|
|
minimum: 32
|
|
maximum: 128
|
|
|
|
required:
|
|
- compatible
|
|
- reg
|
|
- gpio-controller
|
|
- '#gpio-cells'
|
|
- ngpios
|
|
|
|
additionalProperties: false
|
|
|
|
additionalProperties: false
|
|
|
|
required:
|
|
- compatible
|
|
- reg
|
|
- clocks
|
|
- microchip,sgpio-port-ranges
|
|
- "#address-cells"
|
|
- "#size-cells"
|
|
|
|
examples:
|
|
- |
|
|
#include <dt-bindings/interrupt-controller/arm-gic.h>
|
|
sgpio2: gpio@1101059c {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
compatible = "microchip,sparx5-sgpio";
|
|
clocks = <&sys_clk>;
|
|
pinctrl-0 = <&sgpio2_pins>;
|
|
pinctrl-names = "default";
|
|
reg = <0x1101059c 0x118>;
|
|
microchip,sgpio-port-ranges = <0 0>, <16 18>, <28 31>;
|
|
bus-frequency = <25000000>;
|
|
sgpio_in2: gpio@0 {
|
|
reg = <0>;
|
|
compatible = "microchip,sparx5-sgpio-bank";
|
|
gpio-controller;
|
|
#gpio-cells = <3>;
|
|
ngpios = <96>;
|
|
interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
|
|
interrupt-controller;
|
|
#interrupt-cells = <3>;
|
|
};
|
|
sgpio_out2: gpio@1 {
|
|
compatible = "microchip,sparx5-sgpio-bank";
|
|
reg = <1>;
|
|
gpio-controller;
|
|
#gpio-cells = <3>;
|
|
ngpios = <96>;
|
|
};
|
|
};
|