266 lines
8.7 KiB
Plaintext
266 lines
8.7 KiB
Plaintext
This document describes the device tree bindings associated with the
|
|
keystone network coprocessor(NetCP) driver support.
|
|
|
|
The network coprocessor (NetCP) is a hardware accelerator that processes
|
|
Ethernet packets. NetCP has a gigabit Ethernet (GbE) subsystem with a ethernet
|
|
switch sub-module to send and receive packets. NetCP also includes a packet
|
|
accelerator (PA) module to perform packet classification operations such as
|
|
header matching, and packet modification operations such as checksum
|
|
generation. NetCP can also optionally include a Security Accelerator (SA)
|
|
capable of performing IPSec operations on ingress/egress packets.
|
|
|
|
Keystone II SoC's also have a 10 Gigabit Ethernet Subsystem (XGbE) which
|
|
includes a 3-port Ethernet switch sub-module capable of 10Gb/s and 1Gb/s rates
|
|
per Ethernet port.
|
|
|
|
Keystone NetCP driver has a plug-in module architecture where each of the NetCP
|
|
sub-modules exist as a loadable kernel module which plug in to the netcp core.
|
|
These sub-modules are represented as "netcp-devices" in the dts bindings. It is
|
|
mandatory to have the ethernet switch sub-module for the ethernet interface to
|
|
be operational. Any other sub-module like the PA is optional.
|
|
|
|
NetCP Ethernet SubSystem Layout:
|
|
|
|
-----------------------------
|
|
NetCP subsystem(10G or 1G)
|
|
-----------------------------
|
|
|
|
|
|-> NetCP Devices -> |
|
|
| |-> GBE/XGBE Switch
|
|
| |
|
|
| |-> Packet Accelerator
|
|
| |
|
|
| |-> Security Accelerator
|
|
|
|
|
|
|
|
|
|
|
|-> NetCP Interfaces -> |
|
|
|-> Ethernet Port 0
|
|
|
|
|
|-> Ethernet Port 1
|
|
|
|
|
|-> Ethernet Port 2
|
|
|
|
|
|-> Ethernet Port 3
|
|
|
|
|
|
NetCP subsystem properties:
|
|
Required properties:
|
|
- compatible: Should be "ti,netcp-1.0"
|
|
- clocks: phandle to the reference clocks for the subsystem.
|
|
- dma-id: Navigator packet dma instance id.
|
|
- ranges: address range of NetCP (includes, Ethernet SS, PA and SA)
|
|
|
|
Optional properties:
|
|
- reg: register location and the size for the following register
|
|
regions in the specified order.
|
|
- Efuse MAC address register
|
|
- dma-coherent: Present if dma operations are coherent
|
|
- big-endian: Keystone devices can be operated in a mode where the DSP is in
|
|
the big endian mode. In such cases enable this option. This
|
|
option should also be enabled if the ARM is operated in
|
|
big endian mode with the DSP in little endian.
|
|
|
|
NetCP device properties: Device specification for NetCP sub-modules.
|
|
1Gb/10Gb (gbe/xgbe) ethernet switch sub-module specifications.
|
|
Required properties:
|
|
- label: Must be "netcp-gbe" for 1Gb & "netcp-xgbe" for 10Gb.
|
|
- compatible: Must be one of below:-
|
|
"ti,netcp-gbe" for 1GbE on NetCP 1.4
|
|
"ti,netcp-gbe-5" for 1GbE N NetCP 1.5 (N=5)
|
|
"ti,netcp-gbe-9" for 1GbE N NetCP 1.5 (N=9)
|
|
"ti,netcp-gbe-2" for 1GbE N NetCP 1.5 (N=2)
|
|
"ti,netcp-xgbe" for 10 GbE
|
|
|
|
- reg: register location and the size for the following register
|
|
regions in the specified order.
|
|
- switch subsystem registers
|
|
- sgmii port3/4 module registers (only for NetCP 1.4)
|
|
- switch module registers
|
|
- serdes registers (only for 10G)
|
|
|
|
NetCP 1.4 ethss, here is the order
|
|
index #0 - switch subsystem registers
|
|
index #1 - sgmii port3/4 module registers
|
|
index #2 - switch module registers
|
|
|
|
NetCP 1.5 ethss 9 port, 5 port and 2 port
|
|
index #0 - switch subsystem registers
|
|
index #1 - switch module registers
|
|
index #2 - serdes registers
|
|
|
|
- tx-channel: the navigator packet dma channel name for tx.
|
|
- tx-queue: the navigator queue number associated with the tx dma channel.
|
|
- interfaces: specification for each of the switch port to be registered as a
|
|
network interface in the stack.
|
|
-- slave-port: Switch port number, 0 based numbering.
|
|
-- link-interface: type of link interface, supported options are
|
|
- mac<->mac auto negotiate mode: 0
|
|
- mac<->phy mode: 1
|
|
- mac<->mac forced mode: 2
|
|
- mac<->fiber mode: 3
|
|
- mac<->phy mode with no mdio: 4
|
|
- 10Gb mac<->phy mode : 10
|
|
- 10Gb mac<->mac forced mode : 11
|
|
----phy-handle: phandle to PHY device
|
|
|
|
- cpts: sub-node time synchronization (CPTS) submodule configuration
|
|
-- clocks: CPTS reference clock. Should point on cpts-refclk-mux clock.
|
|
-- clock-names: should be "cpts"
|
|
-- cpts-refclk-mux: multiplexer clock definition sub-node for CPTS reference (RFTCLK) clock
|
|
--- #clock-cells: should be 0
|
|
--- clocks: list of CPTS reference (RFTCLK) clock's parents as defined in Data manual
|
|
--- ti,mux-tbl: array of multiplexer indexes as defined in Data manual
|
|
--- assigned-clocks: should point on cpts-refclk-mux clock
|
|
--- assigned-clock-parents: should point on required RFTCLK clock parent to be selected
|
|
-- cpts_clock_mult: (optional) Numerator to convert input clock ticks
|
|
into nanoseconds
|
|
-- cpts_clock_shift: (optional) Denominator to convert input clock ticks into
|
|
nanoseconds.
|
|
Mult and shift will be calculated basing on CPTS
|
|
rftclk frequency if both cpts_clock_shift and
|
|
cpts_clock_mult properties are not provided.
|
|
|
|
Optional properties:
|
|
- enable-ale: NetCP driver keeps the address learning feature in the ethernet
|
|
switch module disabled. This attribute is to enable the address
|
|
learning.
|
|
- secondary-slave-ports: specification for each of the switch port not be
|
|
registered as a network interface. NetCP driver
|
|
will only initialize these ports and attach PHY
|
|
driver to them if needed.
|
|
|
|
NetCP interface properties: Interface specification for NetCP sub-modules.
|
|
Required properties:
|
|
- rx-channel: the navigator packet dma channel name for rx.
|
|
- rx-queue: the navigator queue number associated with rx dma channel.
|
|
- rx-pool: specifies the number of descriptors to be used & the region-id
|
|
for creating the rx descriptor pool.
|
|
- tx-pool: specifies the number of descriptors to be used & the region-id
|
|
for creating the tx descriptor pool.
|
|
- rx-queue-depth: number of descriptors in each of the free descriptor
|
|
queue (FDQ) for the pktdma Rx flow. There can be at
|
|
present a maximum of 4 queues per Rx flow.
|
|
- rx-buffer-size: the buffer size for each of the Rx flow FDQ.
|
|
- tx-completion-queue: the navigator queue number where the descriptors are
|
|
recycled after Tx DMA completion.
|
|
|
|
Optional properties:
|
|
- efuse-mac: If this is 1, then the MAC address for the interface is
|
|
obtained from the device efuse mac address register.
|
|
If this is 2, the two DWORDs occupied by the MAC address
|
|
are swapped. The netcp driver will swap the two DWORDs
|
|
back to the proper order when this property is set to 2
|
|
when it obtains the mac address from efuse.
|
|
- "netcp-device label": phandle to the device specification for each of NetCP
|
|
sub-module attached to this interface.
|
|
|
|
The MAC address will be determined using the optional properties defined in
|
|
ethernet.txt and only if efuse-mac is set to 0. If all of the optional MAC
|
|
address properties are not present, then the driver will use a random MAC
|
|
address.
|
|
|
|
Example binding:
|
|
|
|
netcp: netcp@2000000 {
|
|
reg = <0x2620110 0x8>;
|
|
reg-names = "efuse";
|
|
compatible = "ti,netcp-1.0";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
ranges = <0 0x2000000 0xfffff>;
|
|
clocks = <&papllclk>, <&clkcpgmac>, <&chipclk12>;
|
|
dma-coherent;
|
|
/* big-endian; */
|
|
dma-id = <0>;
|
|
|
|
netcp-devices {
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
ranges;
|
|
gbe@90000 {
|
|
label = "netcp-gbe";
|
|
reg = <0x90000 0x300>, <0x90400 0x400>, <0x90800 0x700>;
|
|
/* enable-ale; */
|
|
tx-queue = <648>;
|
|
tx-channel = <8>;
|
|
|
|
cpts {
|
|
clocks = <&cpts_refclk_mux>;
|
|
clock-names = "cpts";
|
|
|
|
cpts_refclk_mux: cpts-refclk-mux {
|
|
#clock-cells = <0>;
|
|
clocks = <&chipclk12>, <&chipclk13>,
|
|
<&timi0>, <&timi1>,
|
|
<&tsipclka>, <&tsrefclk>,
|
|
<&tsipclkb>;
|
|
ti,mux-tbl = <0x0>, <0x1>, <0x2>,
|
|
<0x3>, <0x4>, <0x8>, <0xC>;
|
|
assigned-clocks = <&cpts_refclk_mux>;
|
|
assigned-clock-parents = <&chipclk12>;
|
|
};
|
|
};
|
|
|
|
interfaces {
|
|
gbe0: interface-0 {
|
|
slave-port = <0>;
|
|
link-interface = <4>;
|
|
};
|
|
gbe1: interface-1 {
|
|
slave-port = <1>;
|
|
link-interface = <4>;
|
|
};
|
|
};
|
|
|
|
secondary-slave-ports {
|
|
port-2 {
|
|
slave-port = <2>;
|
|
link-interface = <2>;
|
|
};
|
|
port-3 {
|
|
slave-port = <3>;
|
|
link-interface = <2>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
netcp-interfaces {
|
|
interface-0 {
|
|
rx-channel = <22>;
|
|
rx-pool = <1024 12>;
|
|
tx-pool = <1024 12>;
|
|
rx-queue-depth = <128 128 0 0>;
|
|
rx-buffer-size = <1518 4096 0 0>;
|
|
rx-queue = <8704>;
|
|
tx-completion-queue = <8706>;
|
|
efuse-mac = <1>;
|
|
netcp-gbe = <&gbe0>;
|
|
|
|
};
|
|
interface-1 {
|
|
rx-channel = <23>;
|
|
rx-pool = <1024 12>;
|
|
tx-pool = <1024 12>;
|
|
rx-queue-depth = <128 128 0 0>;
|
|
rx-buffer-size = <1518 4096 0 0>;
|
|
rx-queue = <8705>;
|
|
tx-completion-queue = <8707>;
|
|
efuse-mac = <0>;
|
|
local-mac-address = [02 18 31 7e 3e 6f];
|
|
netcp-gbe = <&gbe1>;
|
|
};
|
|
};
|
|
};
|
|
|
|
CPTS board configuration - select external CPTS RFTCLK:
|
|
|
|
&tsrefclk{
|
|
clock-frequency = <500000000>;
|
|
};
|
|
|
|
&cpts_refclk_mux {
|
|
assigned-clock-parents = <&tsrefclk>;
|
|
};
|