2134 lines
66 KiB
Plaintext
2134 lines
66 KiB
Plaintext
# SPDX-License-Identifier: GPL-2.0-only
|
|
|
|
#
|
|
# Watchdog device configuration
|
|
#
|
|
|
|
menuconfig WATCHDOG
|
|
bool "Watchdog Timer Support"
|
|
help
|
|
If you say Y here (and to one of the following options) and create a
|
|
character special file /dev/watchdog with major number 10 and minor
|
|
number 130 using mknod ("man mknod"), you will get a watchdog, i.e.:
|
|
subsequently opening the file and then failing to write to it for
|
|
longer than 1 minute will result in rebooting the machine. This
|
|
could be useful for a networked machine that needs to come back
|
|
on-line as fast as possible after a lock-up. There's both a watchdog
|
|
implementation entirely in software (which can sometimes fail to
|
|
reboot the machine) and a driver for hardware watchdog boards, which
|
|
are more robust and can also keep track of the temperature inside
|
|
your computer. For details, read
|
|
<file:Documentation/watchdog/watchdog-api.rst> in the kernel source.
|
|
|
|
The watchdog is usually used together with the watchdog daemon
|
|
which is available from
|
|
<https://ibiblio.org/pub/Linux/system/daemons/watchdog/>. This daemon
|
|
can also monitor NFS connections and can reboot the machine when the
|
|
process table is full.
|
|
|
|
If unsure, say N.
|
|
|
|
if WATCHDOG
|
|
|
|
config WATCHDOG_CORE
|
|
tristate "WatchDog Timer Driver Core"
|
|
help
|
|
Say Y here if you want to use the new watchdog timer driver core.
|
|
This driver provides a framework for all watchdog timer drivers
|
|
and gives them the /dev/watchdog interface (and later also the
|
|
sysfs interface).
|
|
|
|
config WATCHDOG_NOWAYOUT
|
|
bool "Disable watchdog shutdown on close"
|
|
help
|
|
The default watchdog behaviour (which you get if you say N here) is
|
|
to stop the timer if the process managing it closes the file
|
|
/dev/watchdog. It's always remotely possible that this process might
|
|
get killed. If you say Y here, the watchdog cannot be stopped once
|
|
it has been started.
|
|
|
|
config WATCHDOG_HANDLE_BOOT_ENABLED
|
|
bool "Update boot-enabled watchdog until userspace takes over"
|
|
default y
|
|
help
|
|
The default watchdog behaviour (which you get if you say Y here) is
|
|
to ping watchdog devices that were enabled before the driver has
|
|
been loaded until control is taken over from userspace using the
|
|
/dev/watchdog file. If you say N here, the kernel will not update
|
|
the watchdog on its own. Thus if your userspace does not start fast
|
|
enough your device will reboot.
|
|
|
|
config WATCHDOG_OPEN_TIMEOUT
|
|
int "Timeout value for opening watchdog device"
|
|
default 0
|
|
help
|
|
The maximum time, in seconds, for which the watchdog framework takes
|
|
care of pinging a hardware watchdog. A value of 0 means infinite. The
|
|
value set here can be overridden by the commandline parameter
|
|
"watchdog.open_timeout".
|
|
|
|
config WATCHDOG_SYSFS
|
|
bool "Read different watchdog information through sysfs"
|
|
help
|
|
Say Y here if you want to enable watchdog device status read through
|
|
sysfs attributes.
|
|
|
|
config WATCHDOG_HRTIMER_PRETIMEOUT
|
|
bool "Enable watchdog hrtimer-based pretimeouts"
|
|
help
|
|
Enable this if you want to use a hrtimer timer based pretimeout for
|
|
watchdogs that do not natively support pretimeout support. Be aware
|
|
that because this pretimeout functionality uses hrtimers, it may not
|
|
be able to fire before the actual watchdog fires in some situations.
|
|
|
|
comment "Watchdog Pretimeout Governors"
|
|
|
|
config WATCHDOG_PRETIMEOUT_GOV
|
|
bool "Enable watchdog pretimeout governors"
|
|
depends on WATCHDOG_CORE
|
|
help
|
|
The option allows to select watchdog pretimeout governors.
|
|
|
|
config WATCHDOG_PRETIMEOUT_GOV_SEL
|
|
tristate
|
|
depends on WATCHDOG_PRETIMEOUT_GOV
|
|
default m
|
|
select WATCHDOG_PRETIMEOUT_GOV_PANIC if WATCHDOG_PRETIMEOUT_GOV_NOOP=n
|
|
|
|
if WATCHDOG_PRETIMEOUT_GOV
|
|
|
|
config WATCHDOG_PRETIMEOUT_GOV_NOOP
|
|
tristate "Noop watchdog pretimeout governor"
|
|
depends on WATCHDOG_CORE
|
|
default WATCHDOG_CORE
|
|
help
|
|
Noop watchdog pretimeout governor, only an informational
|
|
message is added to kernel log buffer.
|
|
|
|
config WATCHDOG_PRETIMEOUT_GOV_PANIC
|
|
tristate "Panic watchdog pretimeout governor"
|
|
depends on WATCHDOG_CORE
|
|
default WATCHDOG_CORE
|
|
help
|
|
Panic watchdog pretimeout governor, on watchdog pretimeout
|
|
event put the kernel into panic.
|
|
|
|
choice
|
|
prompt "Default Watchdog Pretimeout Governor"
|
|
default WATCHDOG_PRETIMEOUT_DEFAULT_GOV_PANIC
|
|
help
|
|
This option selects a default watchdog pretimeout governor.
|
|
The governor takes its action, if a watchdog is capable
|
|
to report a pretimeout event.
|
|
|
|
config WATCHDOG_PRETIMEOUT_DEFAULT_GOV_NOOP
|
|
bool "noop"
|
|
depends on WATCHDOG_PRETIMEOUT_GOV_NOOP
|
|
help
|
|
Use noop watchdog pretimeout governor by default. If noop
|
|
governor is selected by a user, write a short message to
|
|
the kernel log buffer and don't do any system changes.
|
|
|
|
config WATCHDOG_PRETIMEOUT_DEFAULT_GOV_PANIC
|
|
bool "panic"
|
|
depends on WATCHDOG_PRETIMEOUT_GOV_PANIC
|
|
help
|
|
Use panic watchdog pretimeout governor by default, if
|
|
a watchdog pretimeout event happens, consider that
|
|
a watchdog feeder is dead and reboot is unavoidable.
|
|
|
|
endchoice
|
|
|
|
endif # WATCHDOG_PRETIMEOUT_GOV
|
|
|
|
#
|
|
# General Watchdog drivers
|
|
#
|
|
|
|
comment "Watchdog Device Drivers"
|
|
|
|
# Architecture Independent
|
|
|
|
config SOFT_WATCHDOG
|
|
tristate "Software watchdog"
|
|
select WATCHDOG_CORE
|
|
help
|
|
A software monitoring watchdog. This will fail to reboot your system
|
|
from some situations that the hardware watchdog will recover
|
|
from. Equally it's a lot cheaper to install.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called softdog.
|
|
|
|
config SOFT_WATCHDOG_PRETIMEOUT
|
|
bool "Software watchdog pretimeout governor support"
|
|
depends on SOFT_WATCHDOG && WATCHDOG_PRETIMEOUT_GOV
|
|
help
|
|
Enable this if you want to use pretimeout governors with the software
|
|
watchdog. Be aware that governors might affect the watchdog because it
|
|
is purely software, e.g. the panic governor will stall it!
|
|
|
|
config BD957XMUF_WATCHDOG
|
|
tristate "ROHM BD9576MUF and BD9573MUF PMIC Watchdog"
|
|
depends on MFD_ROHM_BD957XMUF
|
|
select WATCHDOG_CORE
|
|
help
|
|
Support for the watchdog in the ROHM BD9576 and BD9573 PMICs.
|
|
These PMIC ICs contain watchdog block which can be configured
|
|
to toggle reset line if SoC fails to ping watchdog via GPIO.
|
|
|
|
Say Y here to include support for the ROHM BD9576 or BD9573
|
|
watchdog. Alternatively say M to compile the driver as a module,
|
|
which will be called bd9576_wdt.
|
|
|
|
config DA9052_WATCHDOG
|
|
tristate "Dialog DA9052 Watchdog"
|
|
depends on PMIC_DA9052 || COMPILE_TEST
|
|
select WATCHDOG_CORE
|
|
help
|
|
Support for the watchdog in the DA9052 PMIC. Watchdog trigger
|
|
cause system reset.
|
|
|
|
Say Y here to include support for the DA9052 watchdog.
|
|
Alternatively say M to compile the driver as a module,
|
|
which will be called da9052_wdt.
|
|
|
|
config DA9055_WATCHDOG
|
|
tristate "Dialog Semiconductor DA9055 Watchdog"
|
|
depends on MFD_DA9055 || COMPILE_TEST
|
|
select WATCHDOG_CORE
|
|
help
|
|
If you say yes here you get support for watchdog on the Dialog
|
|
Semiconductor DA9055 PMIC.
|
|
|
|
This driver can also be built as a module. If so, the module
|
|
will be called da9055_wdt.
|
|
|
|
config DA9063_WATCHDOG
|
|
tristate "Dialog DA9063 Watchdog"
|
|
depends on MFD_DA9063 || COMPILE_TEST
|
|
select WATCHDOG_CORE
|
|
help
|
|
Support for the watchdog in the DA9063 PMIC.
|
|
|
|
This driver can be built as a module. The module name is da9063_wdt.
|
|
|
|
config DA9062_WATCHDOG
|
|
tristate "Dialog DA9062/61 Watchdog"
|
|
depends on MFD_DA9062 || COMPILE_TEST
|
|
depends on I2C
|
|
select WATCHDOG_CORE
|
|
help
|
|
Support for the watchdog in the DA9062 and DA9061 PMICs.
|
|
|
|
This driver can be built as a module. The module name is da9062_wdt.
|
|
|
|
config GPIO_WATCHDOG
|
|
tristate "Watchdog device controlled through GPIO-line"
|
|
depends on OF_GPIO
|
|
select WATCHDOG_CORE
|
|
help
|
|
If you say yes here you get support for watchdog device
|
|
controlled through GPIO-line.
|
|
|
|
config GPIO_WATCHDOG_ARCH_INITCALL
|
|
bool "Register the watchdog as early as possible"
|
|
depends on GPIO_WATCHDOG=y
|
|
help
|
|
In some situations, the default initcall level (module_init)
|
|
in not early enough in the boot process to avoid the watchdog
|
|
to be triggered.
|
|
If you say yes here, the initcall level would be raised to
|
|
arch_initcall.
|
|
If in doubt, say N.
|
|
|
|
config MENF21BMC_WATCHDOG
|
|
tristate "MEN 14F021P00 BMC Watchdog"
|
|
depends on MFD_MENF21BMC || COMPILE_TEST
|
|
depends on I2C
|
|
select WATCHDOG_CORE
|
|
help
|
|
Say Y here to include support for the MEN 14F021P00 BMC Watchdog.
|
|
|
|
This driver can also be built as a module. If so the module
|
|
will be called menf21bmc_wdt.
|
|
|
|
config MENZ069_WATCHDOG
|
|
tristate "MEN 16Z069 Watchdog"
|
|
depends on MCB
|
|
select WATCHDOG_CORE
|
|
help
|
|
Say Y here to include support for the MEN 16Z069 Watchdog.
|
|
|
|
This driver can also be built as a module. If so the module
|
|
will be called menz069_wdt.
|
|
|
|
config WDAT_WDT
|
|
tristate "ACPI Watchdog Action Table (WDAT)"
|
|
depends on ACPI
|
|
select WATCHDOG_CORE
|
|
select ACPI_WATCHDOG
|
|
help
|
|
This driver adds support for systems with ACPI Watchdog Action
|
|
Table (WDAT) table. Servers typically have this but it can be
|
|
found on some desktop machines as well. This driver will take
|
|
over the native iTCO watchdog driver found on many Intel CPUs.
|
|
|
|
To compile this driver as module, choose M here: the module will
|
|
be called wdat_wdt.
|
|
|
|
config WM831X_WATCHDOG
|
|
tristate "WM831x watchdog"
|
|
depends on MFD_WM831X
|
|
select WATCHDOG_CORE
|
|
help
|
|
Support for the watchdog in the WM831x AudioPlus PMICs. When
|
|
the watchdog triggers the system will be reset.
|
|
|
|
config WM8350_WATCHDOG
|
|
tristate "WM8350 watchdog"
|
|
depends on MFD_WM8350
|
|
select WATCHDOG_CORE
|
|
help
|
|
Support for the watchdog in the WM8350 AudioPlus PMIC. When
|
|
the watchdog triggers the system will be reset.
|
|
|
|
config XILINX_WATCHDOG
|
|
tristate "Xilinx Watchdog timer"
|
|
depends on HAS_IOMEM
|
|
select WATCHDOG_CORE
|
|
help
|
|
Watchdog driver for the xps_timebase_wdt IP core.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called of_xilinx_wdt.
|
|
|
|
config ZIIRAVE_WATCHDOG
|
|
tristate "Zodiac RAVE Watchdog Timer"
|
|
depends on I2C
|
|
select WATCHDOG_CORE
|
|
help
|
|
Watchdog driver for the Zodiac Aerospace RAVE Switch Watchdog
|
|
Processor.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called ziirave_wdt.
|
|
|
|
config RAVE_SP_WATCHDOG
|
|
tristate "RAVE SP Watchdog timer"
|
|
depends on RAVE_SP_CORE
|
|
depends on NVMEM || !NVMEM
|
|
select WATCHDOG_CORE
|
|
help
|
|
Support for the watchdog on RAVE SP device.
|
|
|
|
config MLX_WDT
|
|
tristate "Mellanox Watchdog"
|
|
depends on MELLANOX_PLATFORM
|
|
select WATCHDOG_CORE
|
|
select REGMAP
|
|
help
|
|
This is the driver for the hardware watchdog on Mellanox systems.
|
|
If you are going to use it, say Y here, otherwise N.
|
|
This driver can be used together with the watchdog daemon.
|
|
It can also watch your kernel to make sure it doesn't freeze,
|
|
and if it does, it reboots your system after a certain amount of
|
|
time.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called mlx-wdt.
|
|
|
|
config SL28CPLD_WATCHDOG
|
|
tristate "Kontron sl28cpld Watchdog"
|
|
depends on MFD_SL28CPLD || COMPILE_TEST
|
|
select WATCHDOG_CORE
|
|
help
|
|
Say Y here to include support for the watchdog timer
|
|
on the Kontron sl28 CPLD.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called sl28cpld_wdt.
|
|
|
|
# ALPHA Architecture
|
|
|
|
# ARM Architecture
|
|
|
|
config ARM_SP805_WATCHDOG
|
|
tristate "ARM SP805 Watchdog"
|
|
depends on (ARM || ARM64 || COMPILE_TEST) && ARM_AMBA
|
|
select WATCHDOG_CORE
|
|
help
|
|
ARM Primecell SP805 Watchdog timer. This will reboot your system when
|
|
the timeout is reached.
|
|
|
|
config ARM_SBSA_WATCHDOG
|
|
tristate "ARM SBSA Generic Watchdog"
|
|
depends on ARM64
|
|
depends on ARM_ARCH_TIMER
|
|
select WATCHDOG_CORE
|
|
help
|
|
ARM SBSA Generic Watchdog has two stage timeouts:
|
|
the first signal (WS0) is for alerting the system by interrupt,
|
|
the second one (WS1) is a real hardware reset.
|
|
More details: ARM DEN0029B - Server Base System Architecture (SBSA)
|
|
|
|
This driver can operate ARM SBSA Generic Watchdog as a single stage
|
|
or a two stages watchdog, it depends on the module parameter "action".
|
|
|
|
Note: the maximum timeout in the two stages mode is half of that in
|
|
the single stage mode.
|
|
|
|
To compile this driver as module, choose M here: The module
|
|
will be called sbsa_gwdt.
|
|
|
|
config ARMADA_37XX_WATCHDOG
|
|
tristate "Armada 37xx watchdog"
|
|
depends on ARCH_MVEBU || COMPILE_TEST
|
|
depends on HAS_IOMEM
|
|
select MFD_SYSCON
|
|
select WATCHDOG_CORE
|
|
help
|
|
Say Y here to include support for the watchdog timer found on
|
|
Marvell Armada 37xx SoCs.
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called armada_37xx_wdt.
|
|
|
|
config ASM9260_WATCHDOG
|
|
tristate "Alphascale ASM9260 watchdog"
|
|
depends on MACH_ASM9260 || COMPILE_TEST
|
|
depends on OF
|
|
select WATCHDOG_CORE
|
|
select RESET_CONTROLLER
|
|
help
|
|
Watchdog timer embedded into Alphascale asm9260 chips. This will
|
|
reboot your system when the timeout is reached.
|
|
|
|
config AT91RM9200_WATCHDOG
|
|
tristate "AT91RM9200 watchdog"
|
|
depends on (SOC_AT91RM9200 && MFD_SYSCON) || COMPILE_TEST
|
|
help
|
|
Watchdog timer embedded into AT91RM9200 chips. This will reboot your
|
|
system when the timeout is reached.
|
|
|
|
config AT91SAM9X_WATCHDOG
|
|
tristate "AT91SAM9X / AT91CAP9 watchdog"
|
|
depends on ARCH_AT91 || COMPILE_TEST
|
|
select WATCHDOG_CORE
|
|
help
|
|
Watchdog timer embedded into AT91SAM9X and AT91CAP9 chips. This will
|
|
reboot your system when the timeout is reached.
|
|
|
|
config SAMA5D4_WATCHDOG
|
|
tristate "Atmel SAMA5D4 Watchdog Timer"
|
|
depends on ARCH_AT91 || COMPILE_TEST
|
|
select WATCHDOG_CORE
|
|
help
|
|
Atmel SAMA5D4 watchdog timer is embedded into SAMA5D4 chips.
|
|
Its Watchdog Timer Mode Register can be written more than once.
|
|
This will reboot your system when the timeout is reached.
|
|
|
|
config CADENCE_WATCHDOG
|
|
tristate "Cadence Watchdog Timer"
|
|
depends on HAS_IOMEM
|
|
select WATCHDOG_CORE
|
|
help
|
|
Say Y here if you want to include support for the watchdog
|
|
timer in the Xilinx Zynq.
|
|
|
|
config 21285_WATCHDOG
|
|
tristate "DC21285 watchdog"
|
|
depends on FOOTBRIDGE
|
|
help
|
|
The Intel Footbridge chip contains a built-in watchdog circuit. Say Y
|
|
here if you wish to use this. Alternatively say M to compile the
|
|
driver as a module, which will be called wdt285.
|
|
|
|
This driver does not work on all machines. In particular, early CATS
|
|
boards have hardware problems that will cause the machine to simply
|
|
lock up if the watchdog fires.
|
|
|
|
"If in doubt, leave it out" - say N.
|
|
|
|
config 977_WATCHDOG
|
|
tristate "NetWinder WB83C977 watchdog"
|
|
depends on (FOOTBRIDGE && ARCH_NETWINDER) || (ARM && COMPILE_TEST)
|
|
help
|
|
Say Y here to include support for the WB977 watchdog included in
|
|
NetWinder machines. Alternatively say M to compile the driver as
|
|
a module, which will be called wdt977.
|
|
|
|
Not sure? It's safe to say N.
|
|
|
|
config FTWDT010_WATCHDOG
|
|
tristate "Faraday Technology FTWDT010 watchdog"
|
|
depends on ARM || COMPILE_TEST
|
|
select WATCHDOG_CORE
|
|
default ARCH_GEMINI
|
|
help
|
|
Say Y here if to include support for the Faraday Technology
|
|
FTWDT010 watchdog timer embedded in the Cortina Systems Gemini
|
|
family of devices.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called ftwdt010_wdt.
|
|
|
|
config IXP4XX_WATCHDOG
|
|
tristate "IXP4xx Watchdog"
|
|
depends on ARCH_IXP4XX
|
|
select WATCHDOG_CORE
|
|
help
|
|
Say Y here if to include support for the watchdog timer
|
|
in the Intel IXP4xx network processors. This driver can
|
|
be built as a module by choosing M. The module will
|
|
be called ixp4xx_wdt.
|
|
|
|
Note: The internal IXP4xx watchdog does a soft CPU reset
|
|
which doesn't reset any peripherals. There are circumstances
|
|
where the watchdog will fail to reset the board correctly
|
|
(e.g., if the boot ROM is in an unreadable state).
|
|
|
|
Say N if you are unsure.
|
|
|
|
config S3C2410_WATCHDOG
|
|
tristate "S3C2410 Watchdog"
|
|
depends on ARCH_S3C24XX || ARCH_S3C64XX || ARCH_S5PV210 || ARCH_EXYNOS || \
|
|
COMPILE_TEST
|
|
select WATCHDOG_CORE
|
|
select MFD_SYSCON if ARCH_EXYNOS
|
|
help
|
|
Watchdog timer block in the Samsung SoCs. This will reboot
|
|
the system when the timer expires with the watchdog enabled.
|
|
|
|
The driver is limited by the speed of the system's PCLK
|
|
signal, so with reasonably fast systems (PCLK around 50-66MHz)
|
|
then watchdog intervals of over approximately 20seconds are
|
|
unavailable.
|
|
|
|
The driver can be built as a module by choosing M, and will
|
|
be called s3c2410_wdt
|
|
|
|
config SA1100_WATCHDOG
|
|
tristate "SA1100/PXA2xx watchdog"
|
|
depends on ARCH_SA1100 || ARCH_PXA
|
|
help
|
|
Watchdog timer embedded into SA11x0 and PXA2xx chips. This will
|
|
reboot your system when timeout is reached.
|
|
|
|
NOTE: once enabled, this timer cannot be disabled.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called sa1100_wdt.
|
|
|
|
config DW_WATCHDOG
|
|
tristate "Synopsys DesignWare watchdog"
|
|
depends on HAS_IOMEM
|
|
select WATCHDOG_CORE
|
|
help
|
|
Say Y here if to include support for the Synopsys DesignWare
|
|
watchdog timer found in many chips.
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called dw_wdt.
|
|
|
|
config EP93XX_WATCHDOG
|
|
tristate "EP93xx Watchdog"
|
|
depends on ARCH_EP93XX || COMPILE_TEST
|
|
select WATCHDOG_CORE
|
|
help
|
|
Say Y here if to include support for the watchdog timer
|
|
embedded in the Cirrus Logic EP93xx family of devices.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called ep93xx_wdt.
|
|
|
|
config OMAP_WATCHDOG
|
|
tristate "OMAP Watchdog"
|
|
depends on ARCH_OMAP16XX || ARCH_OMAP2PLUS || COMPILE_TEST
|
|
select WATCHDOG_CORE
|
|
help
|
|
Support for TI OMAP1610/OMAP1710/OMAP2420/OMAP3430/OMAP4430 watchdog.
|
|
Say 'Y' here to enable the
|
|
OMAP1610/OMAP1710/OMAP2420/OMAP3430/OMAP4430 watchdog timer.
|
|
|
|
config PNX4008_WATCHDOG
|
|
tristate "LPC32XX Watchdog"
|
|
depends on ARCH_LPC32XX || COMPILE_TEST
|
|
select WATCHDOG_CORE
|
|
help
|
|
Say Y here if to include support for the watchdog timer
|
|
in the LPC32XX processor.
|
|
This driver can be built as a module by choosing M. The module
|
|
will be called pnx4008_wdt.
|
|
|
|
Say N if you are unsure.
|
|
|
|
config IOP_WATCHDOG
|
|
tristate "IOP Watchdog"
|
|
depends on ARCH_IOP13XX
|
|
select WATCHDOG_NOWAYOUT if (ARCH_IOP32X || ARCH_IOP33X)
|
|
help
|
|
Say Y here if to include support for the watchdog timer
|
|
in the Intel IOP3XX & IOP13XX I/O Processors. This driver can
|
|
be built as a module by choosing M. The module will
|
|
be called iop_wdt.
|
|
|
|
Note: The IOP13XX watchdog does an Internal Bus Reset which will
|
|
affect both cores and the peripherals of the IOP. The ATU-X
|
|
and/or ATUe configuration registers will remain intact, but if
|
|
operating as an Root Complex and/or Central Resource, the PCI-X
|
|
and/or PCIe busses will also be reset. THIS IS A VERY BIG HAMMER.
|
|
|
|
config DAVINCI_WATCHDOG
|
|
tristate "DaVinci watchdog"
|
|
depends on ARCH_DAVINCI || ARCH_KEYSTONE || COMPILE_TEST
|
|
select WATCHDOG_CORE
|
|
help
|
|
Say Y here if to include support for the watchdog timer
|
|
in the DaVinci DM644x/DM646x or Keystone processors.
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called davinci_wdt.
|
|
|
|
NOTE: once enabled, this timer cannot be disabled.
|
|
Say N if you are unsure.
|
|
|
|
config K3_RTI_WATCHDOG
|
|
tristate "Texas Instruments K3 RTI watchdog"
|
|
depends on ARCH_K3 || COMPILE_TEST
|
|
select WATCHDOG_CORE
|
|
help
|
|
Say Y here if you want to include support for the K3 watchdog
|
|
timer (RTI module) available in the K3 generation of processors.
|
|
|
|
config ORION_WATCHDOG
|
|
tristate "Orion watchdog"
|
|
depends on ARCH_ORION5X || ARCH_DOVE || MACH_DOVE || ARCH_MVEBU || COMPILE_TEST
|
|
depends on ARM
|
|
select WATCHDOG_CORE
|
|
help
|
|
Say Y here if to include support for the watchdog timer
|
|
in the Marvell Orion5x and Kirkwood ARM SoCs.
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called orion_wdt.
|
|
|
|
config RN5T618_WATCHDOG
|
|
tristate "Ricoh RN5T618 watchdog"
|
|
depends on MFD_RN5T618 || COMPILE_TEST
|
|
select WATCHDOG_CORE
|
|
help
|
|
If you say yes here you get support for watchdog on the Ricoh
|
|
RN5T618 PMIC.
|
|
|
|
This driver can also be built as a module. If so, the module
|
|
will be called rn5t618_wdt.
|
|
|
|
config SUNXI_WATCHDOG
|
|
tristate "Allwinner SoCs watchdog support"
|
|
depends on ARCH_SUNXI || COMPILE_TEST
|
|
select WATCHDOG_CORE
|
|
help
|
|
Say Y here to include support for the watchdog timer
|
|
in Allwinner SoCs.
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called sunxi_wdt.
|
|
|
|
config NPCM7XX_WATCHDOG
|
|
tristate "Nuvoton NPCM750 watchdog"
|
|
depends on ARCH_NPCM || COMPILE_TEST
|
|
default y if ARCH_NPCM7XX
|
|
select WATCHDOG_CORE
|
|
help
|
|
Say Y here to include Watchdog timer support for the
|
|
watchdog embedded into the NPCM7xx.
|
|
This watchdog is used to reset the system and thus cannot be
|
|
compiled as a module.
|
|
|
|
config TWL4030_WATCHDOG
|
|
tristate "TWL4030 Watchdog"
|
|
depends on TWL4030_CORE
|
|
select WATCHDOG_CORE
|
|
help
|
|
Support for TI TWL4030 watchdog. Say 'Y' here to enable the
|
|
watchdog timer support for TWL4030 chips.
|
|
|
|
config STMP3XXX_RTC_WATCHDOG
|
|
tristate "Freescale STMP3XXX & i.MX23/28 watchdog"
|
|
depends on RTC_DRV_STMP || COMPILE_TEST
|
|
select WATCHDOG_CORE
|
|
help
|
|
Say Y here to include support for the watchdog timer inside
|
|
the RTC for the STMP37XX/378X or i.MX23/28 SoC.
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called stmp3xxx_rtc_wdt.
|
|
|
|
config TS4800_WATCHDOG
|
|
tristate "TS-4800 Watchdog"
|
|
depends on HAS_IOMEM && OF
|
|
depends on SOC_IMX51 || COMPILE_TEST
|
|
select WATCHDOG_CORE
|
|
select MFD_SYSCON
|
|
help
|
|
Technologic Systems TS-4800 has watchdog timer implemented in
|
|
an external FPGA. Say Y here if you want to support for the
|
|
watchdog timer on TS-4800 board.
|
|
|
|
config TS72XX_WATCHDOG
|
|
tristate "TS-72XX SBC Watchdog"
|
|
depends on MACH_TS72XX || COMPILE_TEST
|
|
select WATCHDOG_CORE
|
|
help
|
|
Technologic Systems TS-7200, TS-7250 and TS-7260 boards have
|
|
watchdog timer implemented in a external CPLD chip. Say Y here
|
|
if you want to support for the watchdog timer on TS-72XX boards.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called ts72xx_wdt.
|
|
|
|
config MAX63XX_WATCHDOG
|
|
tristate "Max63xx watchdog"
|
|
depends on HAS_IOMEM
|
|
select WATCHDOG_CORE
|
|
help
|
|
Support for memory mapped max63{69,70,71,72,73,74} watchdog timer.
|
|
|
|
config MAX77620_WATCHDOG
|
|
tristate "Maxim Max77620 Watchdog Timer"
|
|
depends on MFD_MAX77620 || COMPILE_TEST
|
|
select WATCHDOG_CORE
|
|
help
|
|
This is the driver for the Max77620 watchdog timer.
|
|
Say 'Y' here to enable the watchdog timer support for
|
|
MAX77620 chips. To compile this driver as a module,
|
|
choose M here: the module will be called max77620_wdt.
|
|
|
|
config IMX2_WDT
|
|
tristate "IMX2+ Watchdog"
|
|
depends on ARCH_MXC || ARCH_LAYERSCAPE || COMPILE_TEST
|
|
select REGMAP_MMIO
|
|
select WATCHDOG_CORE
|
|
help
|
|
This is the driver for the hardware watchdog
|
|
on the Freescale IMX2 and later processors.
|
|
If you have one of these processors and wish to have
|
|
watchdog support enabled, say Y, otherwise say N.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called imx2_wdt.
|
|
|
|
config IMX_SC_WDT
|
|
tristate "IMX SC Watchdog"
|
|
depends on HAVE_ARM_SMCCC
|
|
depends on IMX_SCU
|
|
select WATCHDOG_CORE
|
|
help
|
|
This is the driver for the system controller watchdog
|
|
on the NXP i.MX SoCs with system controller inside, the
|
|
watchdog driver will call ARM SMC API and trap into
|
|
ARM-Trusted-Firmware for operations, ARM-Trusted-Firmware
|
|
will request system controller to execute the operations.
|
|
If you have one of these processors and wish to have
|
|
watchdog support enabled, say Y, otherwise say N.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called imx_sc_wdt.
|
|
|
|
config IMX7ULP_WDT
|
|
tristate "IMX7ULP Watchdog"
|
|
depends on ARCH_MXC || COMPILE_TEST
|
|
select WATCHDOG_CORE
|
|
help
|
|
This is the driver for the hardware watchdog on the Freescale
|
|
IMX7ULP and later processors. If you have one of these
|
|
processors and wish to have watchdog support enabled,
|
|
say Y, otherwise say N.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called imx7ulp_wdt.
|
|
|
|
config UX500_WATCHDOG
|
|
tristate "ST-Ericsson Ux500 watchdog"
|
|
depends on MFD_DB8500_PRCMU
|
|
select WATCHDOG_CORE
|
|
default y
|
|
help
|
|
Say Y here to include Watchdog timer support for the watchdog
|
|
existing in the prcmu of ST-Ericsson Ux500 series platforms.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called ux500_wdt.
|
|
|
|
config RETU_WATCHDOG
|
|
tristate "Retu watchdog"
|
|
depends on MFD_RETU
|
|
select WATCHDOG_CORE
|
|
help
|
|
Retu watchdog driver for Nokia Internet Tablets (770, N800,
|
|
N810). At least on N800 the watchdog cannot be disabled, so
|
|
this driver is essential and you should enable it.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called retu_wdt.
|
|
|
|
config MOXART_WDT
|
|
tristate "MOXART watchdog"
|
|
depends on ARCH_MOXART || COMPILE_TEST
|
|
help
|
|
Say Y here to include Watchdog timer support for the watchdog
|
|
existing on the MOXA ART SoC series platforms.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called moxart_wdt.
|
|
|
|
config ST_LPC_WATCHDOG
|
|
tristate "STMicroelectronics LPC Watchdog"
|
|
depends on ARCH_STI || COMPILE_TEST
|
|
depends on OF
|
|
select WATCHDOG_CORE
|
|
help
|
|
Say Y here to include STMicroelectronics Low Power Controller
|
|
(LPC) based Watchdog timer support.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called st_lpc_wdt.
|
|
|
|
config TEGRA_WATCHDOG
|
|
tristate "Tegra watchdog"
|
|
depends on (ARCH_TEGRA || COMPILE_TEST) && HAS_IOMEM
|
|
select WATCHDOG_CORE
|
|
help
|
|
Say Y here to include support for the watchdog timer
|
|
embedded in NVIDIA Tegra SoCs.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called tegra_wdt.
|
|
|
|
config QCOM_WDT
|
|
tristate "QCOM watchdog"
|
|
depends on HAS_IOMEM
|
|
depends on ARCH_QCOM || COMPILE_TEST
|
|
select WATCHDOG_CORE
|
|
help
|
|
Say Y here to include Watchdog timer support for the watchdog found
|
|
on QCOM chipsets. Currently supported targets are the MSM8960,
|
|
APQ8064, and IPQ8064.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called qcom_wdt.
|
|
|
|
config MESON_GXBB_WATCHDOG
|
|
tristate "Amlogic Meson GXBB SoCs watchdog support"
|
|
depends on ARCH_MESON || COMPILE_TEST
|
|
select WATCHDOG_CORE
|
|
help
|
|
Say Y here to include support for the watchdog timer
|
|
in Amlogic Meson GXBB SoCs.
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called meson_gxbb_wdt.
|
|
|
|
config MESON_WATCHDOG
|
|
tristate "Amlogic Meson SoCs watchdog support"
|
|
depends on ARCH_MESON || COMPILE_TEST
|
|
select WATCHDOG_CORE
|
|
help
|
|
Say Y here to include support for the watchdog timer
|
|
in Amlogic Meson SoCs.
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called meson_wdt.
|
|
|
|
config MEDIATEK_WATCHDOG
|
|
tristate "Mediatek SoCs watchdog support"
|
|
depends on ARCH_MEDIATEK || COMPILE_TEST
|
|
select WATCHDOG_CORE
|
|
select RESET_CONTROLLER
|
|
help
|
|
Say Y here to include support for the watchdog timer
|
|
in Mediatek SoCs.
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called mtk_wdt.
|
|
|
|
config DIGICOLOR_WATCHDOG
|
|
tristate "Conexant Digicolor SoCs watchdog support"
|
|
depends on ARCH_DIGICOLOR || COMPILE_TEST
|
|
select WATCHDOG_CORE
|
|
help
|
|
Say Y here to include support for the watchdog timer
|
|
in Conexant Digicolor SoCs.
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called digicolor_wdt.
|
|
|
|
config ARM_SMC_WATCHDOG
|
|
tristate "ARM Secure Monitor Call based watchdog support"
|
|
depends on ARM || ARM64
|
|
depends on OF
|
|
depends on HAVE_ARM_SMCCC
|
|
select WATCHDOG_CORE
|
|
help
|
|
Say Y here to include support for a watchdog timer
|
|
implemented by the EL3 Secure Monitor on ARM platforms.
|
|
Requires firmware support.
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called arm_smc_wdt.
|
|
|
|
config LPC18XX_WATCHDOG
|
|
tristate "LPC18xx/43xx Watchdog"
|
|
depends on ARCH_LPC18XX || COMPILE_TEST
|
|
depends on HAS_IOMEM
|
|
select WATCHDOG_CORE
|
|
help
|
|
Say Y here if to include support for the watchdog timer
|
|
in NXP LPC SoCs family, which includes LPC18xx/LPC43xx
|
|
processors.
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called lpc18xx_wdt.
|
|
|
|
config RENESAS_WDT
|
|
tristate "Renesas WDT Watchdog"
|
|
depends on ARCH_RENESAS || COMPILE_TEST
|
|
select WATCHDOG_CORE
|
|
help
|
|
This driver adds watchdog support for the integrated watchdogs in the
|
|
Renesas R-Car and other SH-Mobile SoCs (usually named RWDT or SWDT).
|
|
|
|
config RENESAS_RZAWDT
|
|
tristate "Renesas RZ/A WDT Watchdog"
|
|
depends on ARCH_RENESAS || COMPILE_TEST
|
|
select WATCHDOG_CORE
|
|
help
|
|
This driver adds watchdog support for the integrated watchdogs in the
|
|
Renesas RZ/A SoCs. These watchdogs can be used to reset a system.
|
|
|
|
config ASPEED_WATCHDOG
|
|
tristate "Aspeed BMC watchdog support"
|
|
depends on ARCH_ASPEED || COMPILE_TEST
|
|
select WATCHDOG_CORE
|
|
help
|
|
Say Y here to include support for the watchdog timer
|
|
in Aspeed BMC SoCs.
|
|
|
|
This driver is required to reboot the SoC.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called aspeed_wdt.
|
|
|
|
config STM32_WATCHDOG
|
|
tristate "STM32 Independent WatchDoG (IWDG) support"
|
|
depends on ARCH_STM32
|
|
select WATCHDOG_CORE
|
|
default y
|
|
help
|
|
Say Y here to include support for the watchdog timer
|
|
in stm32 SoCs.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called stm32_iwdg.
|
|
|
|
config STPMIC1_WATCHDOG
|
|
tristate "STPMIC1 PMIC watchdog support"
|
|
depends on MFD_STPMIC1
|
|
select WATCHDOG_CORE
|
|
help
|
|
Say Y here to include watchdog support embedded into STPMIC1 PMIC.
|
|
If the watchdog timer expires, stpmic1 will shut down all its power
|
|
supplies.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called spmic1_wdt.
|
|
|
|
config UNIPHIER_WATCHDOG
|
|
tristate "UniPhier watchdog support"
|
|
depends on ARCH_UNIPHIER || COMPILE_TEST
|
|
depends on OF && MFD_SYSCON
|
|
select WATCHDOG_CORE
|
|
help
|
|
Say Y here to include support watchdog timer embedded
|
|
into the UniPhier system.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called uniphier_wdt.
|
|
|
|
config RTD119X_WATCHDOG
|
|
bool "Realtek RTD119x/RTD129x watchdog support"
|
|
depends on ARCH_REALTEK || COMPILE_TEST
|
|
depends on OF
|
|
select WATCHDOG_CORE
|
|
default ARCH_REALTEK
|
|
help
|
|
Say Y here to include support for the watchdog timer in
|
|
Realtek RTD1295 SoCs.
|
|
|
|
config SPRD_WATCHDOG
|
|
tristate "Spreadtrum watchdog support"
|
|
depends on ARCH_SPRD || COMPILE_TEST
|
|
select WATCHDOG_CORE
|
|
help
|
|
Say Y here to include watchdog timer supported
|
|
by Spreadtrum system.
|
|
|
|
config PM8916_WATCHDOG
|
|
tristate "QCOM PM8916 pmic watchdog"
|
|
depends on OF && MFD_SPMI_PMIC
|
|
select WATCHDOG_CORE
|
|
help
|
|
Say Y here to include support watchdog timer embedded into the
|
|
pm8916 module.
|
|
|
|
config VISCONTI_WATCHDOG
|
|
tristate "Toshiba Visconti series watchdog support"
|
|
depends on ARCH_VISCONTI || COMPILE_TEST
|
|
select WATCHDOG_CORE
|
|
help
|
|
Say Y here to include support for the watchdog timer in Toshiba
|
|
Visconti SoCs.
|
|
|
|
config MSC313E_WATCHDOG
|
|
tristate "MStar MSC313e watchdog"
|
|
depends on ARCH_MSTARV7 || COMPILE_TEST
|
|
select WATCHDOG_CORE
|
|
help
|
|
Say Y here to include support for the Watchdog timer embedded
|
|
into MStar MSC313e chips. This will reboot your system when the
|
|
timeout is reached.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called msc313e_wdt.
|
|
|
|
# X86 (i386 + ia64 + x86_64) Architecture
|
|
|
|
config ACQUIRE_WDT
|
|
tristate "Acquire SBC Watchdog Timer"
|
|
depends on X86
|
|
help
|
|
This is the driver for the hardware watchdog on Single Board
|
|
Computers produced by Acquire Inc (and others). This watchdog
|
|
simply watches your kernel to make sure it doesn't freeze, and if
|
|
it does, it reboots your computer after a certain amount of time.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called acquirewdt.
|
|
|
|
Most people will say N.
|
|
|
|
config ADVANTECH_WDT
|
|
tristate "Advantech SBC Watchdog Timer"
|
|
depends on X86
|
|
help
|
|
If you are configuring a Linux kernel for the Advantech single-board
|
|
computer, say `Y' here to support its built-in watchdog timer
|
|
feature. More information can be found at
|
|
<https://www.advantech.com.tw/products/>
|
|
|
|
config ALIM1535_WDT
|
|
tristate "ALi M1535 PMU Watchdog Timer"
|
|
depends on X86 && PCI
|
|
help
|
|
This is the driver for the hardware watchdog on the ALi M1535 PMU.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called alim1535_wdt.
|
|
|
|
Most people will say N.
|
|
|
|
config ALIM7101_WDT
|
|
tristate "ALi M7101 PMU Computer Watchdog"
|
|
depends on PCI
|
|
help
|
|
This is the driver for the hardware watchdog on the ALi M7101 PMU
|
|
as used in the x86 Cobalt servers and also found in some
|
|
SPARC Netra servers too.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called alim7101_wdt.
|
|
|
|
Most people will say N.
|
|
|
|
config EBC_C384_WDT
|
|
tristate "WinSystems EBC-C384 Watchdog Timer"
|
|
depends on X86
|
|
select ISA_BUS_API
|
|
select WATCHDOG_CORE
|
|
help
|
|
Enables watchdog timer support for the watchdog timer on the
|
|
WinSystems EBC-C384 motherboard. The timeout may be configured via
|
|
the timeout module parameter.
|
|
|
|
config F71808E_WDT
|
|
tristate "Fintek F718xx, F818xx Super I/O Watchdog"
|
|
depends on X86
|
|
help
|
|
This is the driver for the hardware watchdog on the Fintek F71808E,
|
|
F71862FG, F71868, F71869, F71882FG, F71889FG, F81803, F81865, and
|
|
F81866 Super I/O controllers.
|
|
|
|
You can compile this driver directly into the kernel, or use
|
|
it as a module. The module will be called f71808e_wdt.
|
|
|
|
config SP5100_TCO
|
|
tristate "AMD/ATI SP5100 TCO Timer/Watchdog"
|
|
depends on X86 && PCI
|
|
select WATCHDOG_CORE
|
|
help
|
|
Hardware watchdog driver for the AMD/ATI SP5100 chipset. The TCO
|
|
(Total Cost of Ownership) timer is a watchdog timer that will reboot
|
|
the machine after its expiration. The expiration time can be
|
|
configured with the "heartbeat" parameter.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called sp5100_tco.
|
|
|
|
config GEODE_WDT
|
|
tristate "AMD Geode CS5535/CS5536 Watchdog"
|
|
depends on CS5535_MFGPT
|
|
help
|
|
This driver enables a watchdog capability built into the
|
|
CS5535/CS5536 companion chips for the AMD Geode GX and LX
|
|
processors. This watchdog watches your kernel to make sure
|
|
it doesn't freeze, and if it does, it reboots your computer after
|
|
a certain amount of time.
|
|
|
|
You can compile this driver directly into the kernel, or use
|
|
it as a module. The module will be called geodewdt.
|
|
|
|
config SC520_WDT
|
|
tristate "AMD Elan SC520 processor Watchdog"
|
|
depends on MELAN || COMPILE_TEST
|
|
help
|
|
This is the driver for the hardware watchdog built in to the
|
|
AMD "Elan" SC520 microcomputer commonly used in embedded systems.
|
|
This watchdog simply watches your kernel to make sure it doesn't
|
|
freeze, and if it does, it reboots your computer after a certain
|
|
amount of time.
|
|
|
|
You can compile this driver directly into the kernel, or use
|
|
it as a module. The module will be called sc520_wdt.
|
|
|
|
config SBC_FITPC2_WATCHDOG
|
|
tristate "Compulab SBC-FITPC2 watchdog"
|
|
depends on X86
|
|
help
|
|
This is the driver for the built-in watchdog timer on the fit-PC2,
|
|
fit-PC2i, CM-iAM single-board computers made by Compulab.
|
|
|
|
It's possible to enable the watchdog timer either from BIOS (F2) or
|
|
from booted Linux.
|
|
When the "Watchdog Timer Value" is enabled one can set 31-255 seconds
|
|
operational range.
|
|
|
|
Entering BIOS setup temporarily disables watchdog operation regardless
|
|
of current state, so system will not be restarted while user is in
|
|
BIOS setup.
|
|
|
|
Once the watchdog is enabled the system will be restarted every
|
|
"Watchdog Timer Value" period, so to prevent it user can restart or
|
|
disable the watchdog.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called sbc_fitpc2_wdt.
|
|
|
|
Most people will say N.
|
|
|
|
config EUROTECH_WDT
|
|
tristate "Eurotech CPU-1220/1410 Watchdog Timer"
|
|
depends on X86
|
|
help
|
|
Enable support for the watchdog timer on the Eurotech CPU-1220 and
|
|
CPU-1410 cards. These are PC/104 SBCs. Spec sheets and product
|
|
information are at <http://www.eurotech.it/>.
|
|
|
|
config IB700_WDT
|
|
tristate "IB700 SBC Watchdog Timer"
|
|
depends on X86
|
|
help
|
|
This is the driver for the hardware watchdog on the IB700 Single
|
|
Board Computer produced by TMC Technology (www.tmc-uk.com). This
|
|
watchdog simply watches your kernel to make sure it doesn't freeze,
|
|
and if it does, it reboots your computer after a certain amount of time.
|
|
|
|
This driver is like the WDT501 driver but for slightly different
|
|
hardware.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called ib700wdt.
|
|
|
|
Most people will say N.
|
|
|
|
config IBMASR
|
|
tristate "IBM Automatic Server Restart"
|
|
depends on X86
|
|
help
|
|
This is the driver for the IBM Automatic Server Restart watchdog
|
|
timer built-in into some eServer xSeries machines.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called ibmasr.
|
|
|
|
config WAFER_WDT
|
|
tristate "ICP Single Board Computer Watchdog Timer"
|
|
depends on X86
|
|
help
|
|
This is a driver for the hardware watchdog on the ICP Single
|
|
Board Computer. This driver is working on (at least) the following
|
|
IPC SBC's: Wafer 5823, Rocky 4783, Rocky 3703 and Rocky 3782.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called wafer5823wdt.
|
|
|
|
config I6300ESB_WDT
|
|
tristate "Intel 6300ESB Timer/Watchdog"
|
|
depends on PCI
|
|
select WATCHDOG_CORE
|
|
help
|
|
Hardware driver for the watchdog timer built into the Intel
|
|
6300ESB controller hub.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called i6300esb.
|
|
|
|
config IE6XX_WDT
|
|
tristate "Intel Atom E6xx Watchdog"
|
|
depends on X86 && PCI
|
|
select WATCHDOG_CORE
|
|
select MFD_CORE
|
|
select LPC_SCH
|
|
help
|
|
Hardware driver for the watchdog timer built into the Intel
|
|
Atom E6XX (TunnelCreek) processor.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called ie6xx_wdt.
|
|
|
|
config INTEL_MID_WATCHDOG
|
|
tristate "Intel MID Watchdog Timer"
|
|
depends on X86_INTEL_MID
|
|
select WATCHDOG_CORE
|
|
help
|
|
Watchdog timer driver built into the Intel SCU for Intel MID
|
|
Platforms.
|
|
|
|
This driver currently supports only the watchdog evolution
|
|
implementation in SCU, available for Merrifield generation.
|
|
|
|
To compile this driver as a module, choose M here.
|
|
|
|
config ITCO_WDT
|
|
tristate "Intel TCO Timer/Watchdog"
|
|
depends on (X86 || IA64) && PCI
|
|
select WATCHDOG_CORE
|
|
depends on I2C || I2C=n
|
|
depends on MFD_INTEL_PMC_BXT || !MFD_INTEL_PMC_BXT
|
|
select LPC_ICH if !EXPERT
|
|
select I2C_I801 if !EXPERT && I2C
|
|
help
|
|
Hardware driver for the intel TCO timer based watchdog devices.
|
|
These drivers are included in the Intel 82801 I/O Controller
|
|
Hub family (from ICH0 up to ICH10) and in the Intel 63xxESB
|
|
controller hub.
|
|
|
|
The TCO (Total Cost of Ownership) timer is a watchdog timer
|
|
that will reboot the machine after its second expiration. The
|
|
expiration time can be configured with the "heartbeat" parameter.
|
|
|
|
On some motherboards the driver may fail to reset the chipset's
|
|
NO_REBOOT flag which prevents the watchdog from rebooting the
|
|
machine. If this is the case you will get a kernel message like
|
|
"failed to reset NO_REBOOT flag, reboot disabled by hardware".
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called iTCO_wdt.
|
|
|
|
config ITCO_VENDOR_SUPPORT
|
|
bool "Intel TCO Timer/Watchdog Specific Vendor Support"
|
|
depends on ITCO_WDT
|
|
help
|
|
Add vendor specific support to the intel TCO timer based watchdog
|
|
devices. At this moment we only have additional support for some
|
|
SuperMicro Inc. motherboards.
|
|
|
|
config IT8712F_WDT
|
|
tristate "IT8712F (Smart Guardian) Watchdog Timer"
|
|
depends on X86
|
|
help
|
|
This is the driver for the built-in watchdog timer on the IT8712F
|
|
Super I/0 chipset used on many motherboards.
|
|
|
|
If the driver does not work, then make sure that the game port in
|
|
the BIOS is enabled.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called it8712f_wdt.
|
|
|
|
config IT87_WDT
|
|
tristate "IT87 Watchdog Timer"
|
|
depends on X86
|
|
select WATCHDOG_CORE
|
|
help
|
|
This is the driver for the hardware watchdog on the ITE IT8607,
|
|
IT8620, IT8622, IT8625, IT8628, IT8655, IT8665, IT8686, IT8702,
|
|
IT8712, IT8716, IT8718, IT8720, IT8721, IT8726, IT8728, and
|
|
IT8783 Super I/O chips.
|
|
|
|
This watchdog simply watches your kernel to make sure it doesn't
|
|
freeze, and if it does, it reboots your computer after a certain
|
|
amount of time.
|
|
|
|
To compile this driver as a module, choose M here: the module will
|
|
be called it87_wdt.
|
|
|
|
config HP_WATCHDOG
|
|
tristate "HP ProLiant iLO2+ Hardware Watchdog Timer"
|
|
select WATCHDOG_CORE
|
|
depends on X86 && PCI
|
|
help
|
|
A software monitoring watchdog and NMI handling driver. This driver
|
|
will detect lockups and provide a stack trace. This is a driver that
|
|
will only load on an HP ProLiant system with a minimum of iLO2 support.
|
|
To compile this driver as a module, choose M here: the module will be
|
|
called hpwdt.
|
|
|
|
config HPWDT_NMI_DECODING
|
|
bool "NMI support for the HP ProLiant iLO2+ Hardware Watchdog Timer"
|
|
depends on HP_WATCHDOG
|
|
default y
|
|
help
|
|
Enables the NMI handler for the watchdog pretimeout NMI and the iLO
|
|
"Generate NMI to System" virtual button. When an NMI is claimed
|
|
by the driver, panic is called.
|
|
|
|
config KEMPLD_WDT
|
|
tristate "Kontron COM Watchdog Timer"
|
|
depends on MFD_KEMPLD
|
|
select WATCHDOG_CORE
|
|
help
|
|
Support for the PLD watchdog on some Kontron ETX and COMexpress
|
|
(ETXexpress) modules
|
|
|
|
This driver can also be built as a module. If so, the module will be
|
|
called kempld_wdt.
|
|
|
|
config SC1200_WDT
|
|
tristate "National Semiconductor PC87307/PC97307 (ala SC1200) Watchdog"
|
|
depends on X86
|
|
help
|
|
This is a driver for National Semiconductor PC87307/PC97307 hardware
|
|
watchdog cards as found on the SC1200. This watchdog is mainly used
|
|
for power management purposes and can be used to power down the device
|
|
during inactivity periods (includes interrupt activity monitoring).
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called sc1200wdt.
|
|
|
|
Most people will say N.
|
|
|
|
config SCx200_WDT
|
|
tristate "National Semiconductor SCx200 Watchdog"
|
|
depends on SCx200 && PCI
|
|
help
|
|
Enable the built-in watchdog timer support on the National
|
|
Semiconductor SCx200 processors.
|
|
|
|
If compiled as a module, it will be called scx200_wdt.
|
|
|
|
config PC87413_WDT
|
|
tristate "NS PC87413 watchdog"
|
|
depends on X86
|
|
help
|
|
This is the driver for the hardware watchdog on the PC87413 chipset
|
|
This watchdog simply watches your kernel to make sure it doesn't
|
|
freeze, and if it does, it reboots your computer after a certain
|
|
amount of time.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called pc87413_wdt.
|
|
|
|
Most people will say N.
|
|
|
|
config NV_TCO
|
|
tristate "nVidia TCO Timer/Watchdog"
|
|
depends on X86 && PCI
|
|
help
|
|
Hardware driver for the TCO timer built into the nVidia Hub family
|
|
(such as the MCP51). The TCO (Total Cost of Ownership) timer is a
|
|
watchdog timer that will reboot the machine after its second
|
|
expiration. The expiration time can be configured with the
|
|
"heartbeat" parameter.
|
|
|
|
On some motherboards the driver may fail to reset the chipset's
|
|
NO_REBOOT flag which prevents the watchdog from rebooting the
|
|
machine. If this is the case you will get a kernel message like
|
|
"failed to reset NO_REBOOT flag, reboot disabled by hardware".
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called nv_tco.
|
|
|
|
config RDC321X_WDT
|
|
tristate "RDC R-321x SoC watchdog"
|
|
depends on X86_RDC321X || COMPILE_TEST
|
|
depends on PCI
|
|
help
|
|
This is the driver for the built in hardware watchdog
|
|
in the RDC R-321x SoC.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called rdc321x_wdt.
|
|
|
|
config 60XX_WDT
|
|
tristate "SBC-60XX Watchdog Timer"
|
|
depends on X86
|
|
help
|
|
This driver can be used with the watchdog timer found on some
|
|
single board computers, namely the 6010 PII based computer.
|
|
It may well work with other cards. It reads port 0x443 to enable
|
|
and re-set the watchdog timer, and reads port 0x45 to disable
|
|
the watchdog. If you have a card that behave in similar ways,
|
|
you can probably make this driver work with your card as well.
|
|
|
|
You can compile this driver directly into the kernel, or use
|
|
it as a module. The module will be called sbc60xxwdt.
|
|
|
|
config SBC8360_WDT
|
|
tristate "SBC8360 Watchdog Timer"
|
|
depends on X86_32
|
|
help
|
|
|
|
This is the driver for the hardware watchdog on the SBC8360 Single
|
|
Board Computer produced by Axiomtek Co., Ltd. (www.axiomtek.com).
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called sbc8360.
|
|
|
|
Most people will say N.
|
|
|
|
config SBC7240_WDT
|
|
tristate "SBC Nano 7240 Watchdog Timer"
|
|
depends on X86_32 && !UML
|
|
help
|
|
This is the driver for the hardware watchdog found on the IEI
|
|
single board computers EPIC Nano 7240 (and likely others). This
|
|
watchdog simply watches your kernel to make sure it doesn't freeze,
|
|
and if it does, it reboots your computer after a certain amount of
|
|
time.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called sbc7240_wdt.
|
|
|
|
config CPU5_WDT
|
|
tristate "SMA CPU5 Watchdog"
|
|
depends on X86
|
|
help
|
|
TBD.
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called cpu5wdt.
|
|
|
|
config SMSC_SCH311X_WDT
|
|
tristate "SMSC SCH311X Watchdog Timer"
|
|
depends on X86
|
|
help
|
|
This is the driver for the hardware watchdog timer on the
|
|
SMSC SCH3112, SCH3114 and SCH3116 Super IO chipset
|
|
(LPC IO with 8042 KBC, Reset Generation, HWM and multiple
|
|
serial ports).
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called sch311x_wdt.
|
|
|
|
config SMSC37B787_WDT
|
|
tristate "Winbond SMsC37B787 Watchdog Timer"
|
|
depends on X86
|
|
help
|
|
This is the driver for the hardware watchdog component on the
|
|
Winbond SMsC37B787 chipset as used on the NetRunner Mainboard
|
|
from Vision Systems and maybe others.
|
|
|
|
This watchdog simply watches your kernel to make sure it doesn't
|
|
freeze, and if it does, it reboots your computer after a certain
|
|
amount of time.
|
|
|
|
Usually a userspace daemon will notify the kernel WDT driver that
|
|
userspace is still alive, at regular intervals.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called smsc37b787_wdt.
|
|
|
|
Most people will say N.
|
|
|
|
config TQMX86_WDT
|
|
tristate "TQ-Systems TQMX86 Watchdog Timer"
|
|
depends on X86
|
|
select WATCHDOG_CORE
|
|
help
|
|
This is the driver for the hardware watchdog timer in the TQMX86 IO
|
|
controller found on some of their ComExpress Modules.
|
|
|
|
To compile this driver as a module, choose M here; the module
|
|
will be called tqmx86_wdt.
|
|
|
|
Most people will say N.
|
|
|
|
config VIA_WDT
|
|
tristate "VIA Watchdog Timer"
|
|
depends on X86 && PCI
|
|
select WATCHDOG_CORE
|
|
help
|
|
This is the driver for the hardware watchdog timer on VIA
|
|
southbridge chipset CX700, VX800/VX820 or VX855/VX875.
|
|
|
|
To compile this driver as a module, choose M here; the module
|
|
will be called via_wdt.
|
|
|
|
Most people will say N.
|
|
|
|
config W83627HF_WDT
|
|
tristate "Watchdog timer for W83627HF/W83627DHG and compatibles"
|
|
depends on X86
|
|
select WATCHDOG_CORE
|
|
help
|
|
This is the driver for the hardware watchdog on the following
|
|
Super I/O chips.
|
|
W83627DHG/DHG-P/EHF/EHG/F/G/HF/S/SF/THF/UHG/UG
|
|
W83637HF
|
|
W83667HG/HG-B
|
|
W83687THF
|
|
W83697HF
|
|
W83697UG
|
|
NCT6775
|
|
NCT6776
|
|
NCT6779
|
|
NCT6791
|
|
NCT6792
|
|
NCT6102D/04D/06D
|
|
NCT6116D
|
|
|
|
This watchdog simply watches your kernel to make sure it doesn't
|
|
freeze, and if it does, it reboots your computer after a certain
|
|
amount of time.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called w83627hf_wdt.
|
|
|
|
Most people will say N.
|
|
|
|
config W83877F_WDT
|
|
tristate "W83877F (EMACS) Watchdog Timer"
|
|
depends on X86
|
|
help
|
|
This is the driver for the hardware watchdog on the W83877F chipset
|
|
as used in EMACS PC-104 motherboards (and likely others). This
|
|
watchdog simply watches your kernel to make sure it doesn't freeze,
|
|
and if it does, it reboots your computer after a certain amount of
|
|
time.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called w83877f_wdt.
|
|
|
|
Most people will say N.
|
|
|
|
config W83977F_WDT
|
|
tristate "W83977F (PCM-5335) Watchdog Timer"
|
|
depends on X86
|
|
help
|
|
This is the driver for the hardware watchdog on the W83977F I/O chip
|
|
as used in AAEON's PCM-5335 SBC (and likely others). This
|
|
watchdog simply watches your kernel to make sure it doesn't freeze,
|
|
and if it does, it reboots your computer after a certain amount of
|
|
time.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called w83977f_wdt.
|
|
|
|
config MACHZ_WDT
|
|
tristate "ZF MachZ Watchdog"
|
|
depends on X86
|
|
help
|
|
If you are using a ZF Micro MachZ processor, say Y here, otherwise
|
|
N. This is the driver for the watchdog timer built-in on that
|
|
processor using ZF-Logic interface. This watchdog simply watches
|
|
your kernel to make sure it doesn't freeze, and if it does, it
|
|
reboots your computer after a certain amount of time.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called machzwd.
|
|
|
|
config SBC_EPX_C3_WATCHDOG
|
|
tristate "Winsystems SBC EPX-C3 watchdog"
|
|
depends on X86
|
|
help
|
|
This is the driver for the built-in watchdog timer on the EPX-C3
|
|
Single-board computer made by Winsystems, Inc.
|
|
|
|
*Note*: This hardware watchdog is not probeable and thus there
|
|
is no way to know if writing to its IO address will corrupt
|
|
your system or have any real effect. The only way to be sure
|
|
that this driver does what you want is to make sure you
|
|
are running it on an EPX-C3 from Winsystems with the watchdog
|
|
timer at IO address 0x1ee and 0x1ef. It will write to both those
|
|
IO ports. Basically, the assumption is made that if you compile
|
|
this driver into your kernel and/or load it as a module, that you
|
|
know what you are doing and that you are in fact running on an
|
|
EPX-C3 board!
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called sbc_epx_c3.
|
|
|
|
config INTEL_MEI_WDT
|
|
tristate "Intel MEI iAMT Watchdog"
|
|
depends on INTEL_MEI && X86
|
|
select WATCHDOG_CORE
|
|
help
|
|
A device driver for the Intel MEI iAMT watchdog.
|
|
|
|
The Intel AMT Watchdog is an OS Health (Hang/Crash) watchdog.
|
|
Whenever the OS hangs or crashes, iAMT will send an event
|
|
to any subscriber to this event. The watchdog doesn't reset the
|
|
the platform.
|
|
|
|
To compile this driver as a module, choose M here:
|
|
the module will be called mei_wdt.
|
|
|
|
config NI903X_WDT
|
|
tristate "NI 903x/913x Watchdog"
|
|
depends on X86 && ACPI
|
|
select WATCHDOG_CORE
|
|
help
|
|
This is the driver for the watchdog timer on the National Instruments
|
|
903x/913x real-time controllers.
|
|
|
|
To compile this driver as a module, choose M here: the module will be
|
|
called ni903x_wdt.
|
|
|
|
config NIC7018_WDT
|
|
tristate "NIC7018 Watchdog"
|
|
depends on X86 && ACPI
|
|
select WATCHDOG_CORE
|
|
help
|
|
Support for National Instruments NIC7018 Watchdog.
|
|
|
|
To compile this driver as a module, choose M here: the module will be
|
|
called nic7018_wdt.
|
|
|
|
# M68K Architecture
|
|
|
|
config M54xx_WATCHDOG
|
|
tristate "MCF54xx watchdog support"
|
|
depends on M548x
|
|
help
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called m54xx_wdt.
|
|
|
|
# MicroBlaze Architecture
|
|
|
|
# MIPS Architecture
|
|
|
|
config ATH79_WDT
|
|
tristate "Atheros AR71XX/AR724X/AR913X hardware watchdog"
|
|
depends on ATH79 || (ARM && COMPILE_TEST)
|
|
help
|
|
Hardware driver for the built-in watchdog timer on the Atheros
|
|
AR71XX/AR724X/AR913X SoCs.
|
|
|
|
config BCM47XX_WDT
|
|
tristate "Broadcom BCM47xx Watchdog Timer"
|
|
depends on BCM47XX || ARCH_BCM_5301X || COMPILE_TEST
|
|
select WATCHDOG_CORE
|
|
help
|
|
Hardware driver for the Broadcom BCM47xx Watchdog Timer.
|
|
|
|
config RC32434_WDT
|
|
tristate "IDT RC32434 SoC Watchdog Timer"
|
|
depends on MIKROTIK_RB532
|
|
help
|
|
Hardware driver for the IDT RC32434 SoC built-in
|
|
watchdog timer.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called rc32434_wdt.
|
|
|
|
config INDYDOG
|
|
tristate "Indy/I2 Hardware Watchdog"
|
|
depends on SGI_HAS_INDYDOG
|
|
help
|
|
Hardware driver for the Indy's/I2's watchdog. This is a
|
|
watchdog timer that will reboot the machine after a 60 second
|
|
timer expired and no process has written to /dev/watchdog during
|
|
that time.
|
|
|
|
config JZ4740_WDT
|
|
tristate "Ingenic jz4740 SoC hardware watchdog"
|
|
depends on MIPS
|
|
depends on COMMON_CLK
|
|
select WATCHDOG_CORE
|
|
select MFD_SYSCON
|
|
help
|
|
Hardware driver for the built-in watchdog timer on Ingenic jz4740 SoCs.
|
|
|
|
config WDT_MTX1
|
|
tristate "MTX-1 Hardware Watchdog"
|
|
depends on MIPS_MTX1 || (MIPS && COMPILE_TEST)
|
|
help
|
|
Hardware driver for the MTX-1 boards. This is a watchdog timer that
|
|
will reboot the machine after a 100 seconds timer expired.
|
|
|
|
config SIBYTE_WDOG
|
|
tristate "Sibyte SoC hardware watchdog"
|
|
depends on CPU_SB1
|
|
help
|
|
Watchdog driver for the built in watchdog hardware in Sibyte
|
|
SoC processors. There are apparently two watchdog timers
|
|
on such processors; this driver supports only the first one,
|
|
because currently Linux only supports exporting one watchdog
|
|
to userspace.
|
|
|
|
To compile this driver as a loadable module, choose M here.
|
|
The module will be called sb_wdog.
|
|
|
|
config AR7_WDT
|
|
tristate "TI AR7 Watchdog Timer"
|
|
depends on AR7 || (MIPS && 32BIT && COMPILE_TEST)
|
|
help
|
|
Hardware driver for the TI AR7 Watchdog Timer.
|
|
|
|
config TXX9_WDT
|
|
tristate "Toshiba TXx9 Watchdog Timer"
|
|
depends on CPU_TX39XX || CPU_TX49XX || (MIPS && COMPILE_TEST)
|
|
select WATCHDOG_CORE
|
|
help
|
|
Hardware driver for the built-in watchdog timer on TXx9 MIPS SoCs.
|
|
|
|
config OCTEON_WDT
|
|
tristate "Cavium OCTEON SOC family Watchdog Timer"
|
|
depends on CAVIUM_OCTEON_SOC
|
|
default y
|
|
select WATCHDOG_CORE
|
|
select EXPORT_UASM if OCTEON_WDT = m
|
|
help
|
|
Hardware driver for OCTEON's on chip watchdog timer.
|
|
Enables the watchdog for all cores running Linux. It
|
|
installs a NMI handler and pokes the watchdog based on an
|
|
interrupt. On first expiration of the watchdog, the
|
|
interrupt handler pokes it. The second expiration causes an
|
|
NMI that prints a message. The third expiration causes a
|
|
global soft reset.
|
|
|
|
When userspace has /dev/watchdog open, no poking is done
|
|
from the first interrupt, it is then only poked when the
|
|
device is written.
|
|
|
|
config BCM63XX_WDT
|
|
tristate "Broadcom BCM63xx hardware watchdog"
|
|
depends on BCM63XX
|
|
help
|
|
Watchdog driver for the built in watchdog hardware in Broadcom
|
|
BCM63xx SoC.
|
|
|
|
To compile this driver as a loadable module, choose M here.
|
|
The module will be called bcm63xx_wdt.
|
|
|
|
config BCM2835_WDT
|
|
tristate "Broadcom BCM2835 hardware watchdog"
|
|
depends on ARCH_BCM2835 || (OF && COMPILE_TEST)
|
|
select WATCHDOG_CORE
|
|
help
|
|
Watchdog driver for the built in watchdog hardware in Broadcom
|
|
BCM2835 SoC.
|
|
|
|
To compile this driver as a loadable module, choose M here.
|
|
The module will be called bcm2835_wdt.
|
|
|
|
config BCM_KONA_WDT
|
|
tristate "BCM Kona Watchdog"
|
|
depends on ARCH_BCM_MOBILE || COMPILE_TEST
|
|
select WATCHDOG_CORE
|
|
help
|
|
Support for the watchdog timer on the following Broadcom BCM281xx
|
|
family, which includes BCM11130, BCM11140, BCM11351, BCM28145 and
|
|
BCM28155 variants.
|
|
|
|
Say 'Y' or 'M' here to enable the driver. The module will be called
|
|
bcm_kona_wdt.
|
|
|
|
config BCM_KONA_WDT_DEBUG
|
|
bool "DEBUGFS support for BCM Kona Watchdog"
|
|
depends on BCM_KONA_WDT
|
|
help
|
|
If enabled, adds /sys/kernel/debug/bcm_kona_wdt/info which provides
|
|
access to the driver's internal data structures as well as watchdog
|
|
timer hardware registres.
|
|
|
|
If in doubt, say 'N'.
|
|
|
|
config BCM7038_WDT
|
|
tristate "BCM7038 Watchdog"
|
|
select WATCHDOG_CORE
|
|
depends on HAS_IOMEM
|
|
depends on ARCH_BRCMSTB || BMIPS_GENERIC || COMPILE_TEST
|
|
help
|
|
Watchdog driver for the built-in hardware in Broadcom 7038 and
|
|
later SoCs used in set-top boxes. BCM7038 was made public
|
|
during the 2004 CES, and since then, many Broadcom chips use this
|
|
watchdog block, including some cable modem chips.
|
|
|
|
config IMGPDC_WDT
|
|
tristate "Imagination Technologies PDC Watchdog Timer"
|
|
depends on HAS_IOMEM
|
|
depends on MIPS || COMPILE_TEST
|
|
select WATCHDOG_CORE
|
|
help
|
|
Driver for Imagination Technologies PowerDown Controller
|
|
Watchdog Timer.
|
|
|
|
To compile this driver as a loadable module, choose M here.
|
|
The module will be called imgpdc_wdt.
|
|
|
|
config LANTIQ_WDT
|
|
tristate "Lantiq SoC watchdog"
|
|
depends on LANTIQ
|
|
select WATCHDOG_CORE
|
|
help
|
|
Hardware driver for the Lantiq SoC Watchdog Timer.
|
|
|
|
config LOONGSON1_WDT
|
|
tristate "Loongson1 SoC hardware watchdog"
|
|
depends on MACH_LOONGSON32
|
|
select WATCHDOG_CORE
|
|
help
|
|
Hardware driver for the Loongson1 SoC Watchdog Timer.
|
|
|
|
config RALINK_WDT
|
|
tristate "Ralink SoC watchdog"
|
|
select WATCHDOG_CORE
|
|
depends on RALINK
|
|
help
|
|
Hardware driver for the Ralink SoC Watchdog Timer.
|
|
|
|
config MT7621_WDT
|
|
tristate "Mediatek SoC watchdog"
|
|
select WATCHDOG_CORE
|
|
depends on SOC_MT7620 || SOC_MT7621
|
|
help
|
|
Hardware driver for the Mediatek/Ralink MT7621/8 SoC Watchdog Timer.
|
|
|
|
config PIC32_WDT
|
|
tristate "Microchip PIC32 hardware watchdog"
|
|
select WATCHDOG_CORE
|
|
depends on MACH_PIC32 || (MIPS && COMPILE_TEST)
|
|
help
|
|
Watchdog driver for the built in watchdog hardware in a PIC32.
|
|
|
|
Configuration bits must be set appropriately for the watchdog to be
|
|
controlled by this driver.
|
|
|
|
To compile this driver as a loadable module, choose M here.
|
|
The module will be called pic32-wdt.
|
|
|
|
config PIC32_DMT
|
|
tristate "Microchip PIC32 Deadman Timer"
|
|
select WATCHDOG_CORE
|
|
depends on MACH_PIC32 || (MIPS && COMPILE_TEST)
|
|
help
|
|
Watchdog driver for PIC32 instruction fetch counting timer. This
|
|
specific timer is typically be used in mission critical and safety
|
|
critical applications, where any single failure of the software
|
|
functionality and sequencing must be detected.
|
|
|
|
To compile this driver as a loadable module, choose M here.
|
|
The module will be called pic32-dmt.
|
|
|
|
# PARISC Architecture
|
|
|
|
# POWERPC Architecture
|
|
|
|
config GEF_WDT
|
|
tristate "GE Watchdog Timer"
|
|
depends on GE_FPGA
|
|
help
|
|
Watchdog timer found in a number of GE single board computers.
|
|
|
|
config MPC5200_WDT
|
|
bool "MPC52xx Watchdog Timer"
|
|
depends on PPC_MPC52xx || COMPILE_TEST
|
|
help
|
|
Use General Purpose Timer (GPT) 0 on the MPC5200 as Watchdog.
|
|
|
|
config 8xxx_WDT
|
|
tristate "MPC8xxx Platform Watchdog Timer"
|
|
depends on PPC_8xx || PPC_83xx || PPC_86xx || PPC_MPC512x
|
|
select WATCHDOG_CORE
|
|
help
|
|
This driver is for a SoC level watchdog that exists on some
|
|
Freescale PowerPC processors. So far this driver supports:
|
|
- MPC8xx watchdogs
|
|
- MPC83xx watchdogs
|
|
- MPC86xx watchdogs
|
|
|
|
For BookE processors (MPC85xx) use the BOOKE_WDT driver instead.
|
|
|
|
config PIKA_WDT
|
|
tristate "PIKA FPGA Watchdog"
|
|
depends on WARP || (PPC64 && COMPILE_TEST)
|
|
default y
|
|
help
|
|
This enables the watchdog in the PIKA FPGA. Currently used on
|
|
the Warp platform.
|
|
|
|
config BOOKE_WDT
|
|
tristate "PowerPC Book-E Watchdog Timer"
|
|
depends on BOOKE || 4xx
|
|
select WATCHDOG_CORE
|
|
help
|
|
Watchdog driver for PowerPC Book-E chips, such as the Freescale
|
|
MPC85xx SOCs and the IBM PowerPC 440.
|
|
|
|
Please see Documentation/watchdog/watchdog-api.rst for
|
|
more information.
|
|
|
|
config BOOKE_WDT_DEFAULT_TIMEOUT
|
|
int "PowerPC Book-E Watchdog Timer Default Timeout"
|
|
depends on BOOKE_WDT
|
|
default 38 if PPC_FSL_BOOK3E
|
|
range 0 63 if PPC_FSL_BOOK3E
|
|
default 3 if !PPC_FSL_BOOK3E
|
|
range 0 3 if !PPC_FSL_BOOK3E
|
|
help
|
|
Select the default watchdog timer period to be used by the PowerPC
|
|
Book-E watchdog driver. A watchdog "event" occurs when the bit
|
|
position represented by this number transitions from zero to one.
|
|
|
|
For Freescale Book-E processors, this is a number between 0 and 63.
|
|
For other Book-E processors, this is a number between 0 and 3.
|
|
|
|
The value can be overridden by the wdt_period command-line parameter.
|
|
|
|
config MEN_A21_WDT
|
|
tristate "MEN A21 VME CPU Carrier Board Watchdog Timer"
|
|
select WATCHDOG_CORE
|
|
depends on GPIOLIB || COMPILE_TEST
|
|
help
|
|
Watchdog driver for MEN A21 VMEbus CPU Carrier Boards.
|
|
|
|
The driver can also be built as a module. If so, the module will be
|
|
called mena21_wdt.
|
|
|
|
If unsure select N here.
|
|
|
|
# PPC64 Architecture
|
|
|
|
config WATCHDOG_RTAS
|
|
tristate "RTAS watchdog"
|
|
depends on PPC_RTAS
|
|
help
|
|
This driver adds watchdog support for the RTAS watchdog.
|
|
|
|
To compile this driver as a module, choose M here. The module
|
|
will be called wdrtas.
|
|
|
|
# S390 Architecture
|
|
|
|
config DIAG288_WATCHDOG
|
|
tristate "System z diag288 Watchdog"
|
|
depends on S390
|
|
select WATCHDOG_CORE
|
|
help
|
|
IBM s/390 and zSeries machines running under z/VM 5.1 or later
|
|
provide a virtual watchdog timer to their guest that cause a
|
|
user define Control Program command to be executed after a
|
|
timeout.
|
|
LPAR provides a very similar interface. This driver handles
|
|
both.
|
|
|
|
To compile this driver as a module, choose M here. The module
|
|
will be called diag288_wdt.
|
|
|
|
# SUPERH (sh + sh64) Architecture
|
|
|
|
config SH_WDT
|
|
tristate "SuperH Watchdog"
|
|
depends on SUPERH && (CPU_SH3 || CPU_SH4 || COMPILE_TEST)
|
|
select WATCHDOG_CORE
|
|
help
|
|
This driver adds watchdog support for the integrated watchdog in the
|
|
SuperH processors. If you have one of these processors and wish
|
|
to have watchdog support enabled, say Y, otherwise say N.
|
|
|
|
As a side note, saying Y here will automatically boost HZ to 1000
|
|
so that the timer has a chance to clear the overflow counter. On
|
|
slower systems (such as the SH-2 and SH-3) this will likely yield
|
|
some performance issues. As such, the WDT should be avoided here
|
|
unless it is absolutely necessary.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called shwdt.
|
|
|
|
# SPARC Architecture
|
|
|
|
# SPARC64 Architecture
|
|
|
|
config WATCHDOG_CP1XXX
|
|
tristate "CP1XXX Hardware Watchdog support"
|
|
depends on SPARC64 && PCI
|
|
help
|
|
This is the driver for the hardware watchdog timers present on
|
|
Sun Microsystems CompactPCI models CP1400 and CP1500.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called cpwatchdog.
|
|
|
|
If you do not have a CompactPCI model CP1400 or CP1500, or
|
|
another UltraSPARC-IIi-cEngine boardset with hardware watchdog,
|
|
you should say N to this option.
|
|
|
|
config WATCHDOG_RIO
|
|
tristate "RIO Hardware Watchdog support"
|
|
depends on SPARC64 && PCI
|
|
help
|
|
Say Y here to support the hardware watchdog capability on Sun RIO
|
|
machines. The watchdog timeout period is normally one minute but
|
|
can be changed with a boot-time parameter.
|
|
|
|
config WATCHDOG_SUN4V
|
|
tristate "Sun4v Watchdog support"
|
|
select WATCHDOG_CORE
|
|
depends on SPARC64
|
|
help
|
|
Say Y here to support the hypervisor watchdog capability embedded
|
|
in the SPARC sun4v architecture.
|
|
|
|
To compile this driver as a module, choose M here. The module will
|
|
be called sun4v_wdt.
|
|
|
|
# XTENSA Architecture
|
|
|
|
# Xen Architecture
|
|
|
|
config XEN_WDT
|
|
tristate "Xen Watchdog support"
|
|
depends on XEN
|
|
select WATCHDOG_CORE
|
|
help
|
|
Say Y here to support the hypervisor watchdog capability provided
|
|
by Xen 4.0 and newer. The watchdog timeout period is normally one
|
|
minute but can be changed with a boot-time parameter.
|
|
|
|
config UML_WATCHDOG
|
|
tristate "UML watchdog"
|
|
depends on UML || COMPILE_TEST
|
|
|
|
#
|
|
# ISA-based Watchdog Cards
|
|
#
|
|
|
|
comment "ISA-based Watchdog Cards"
|
|
depends on ISA
|
|
|
|
config PCWATCHDOG
|
|
tristate "Berkshire Products ISA-PC Watchdog"
|
|
depends on ISA
|
|
help
|
|
This is the driver for the Berkshire Products ISA-PC Watchdog card.
|
|
This card simply watches your kernel to make sure it doesn't freeze,
|
|
and if it does, it reboots your computer after a certain amount of
|
|
time. This driver is like the WDT501 driver but for different
|
|
hardware. Please read <file:Documentation/watchdog/pcwd-watchdog.rst>.
|
|
The PC watchdog cards can be ordered from <http://www.berkprod.com/>.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called pcwd.
|
|
|
|
Most people will say N.
|
|
|
|
config MIXCOMWD
|
|
tristate "Mixcom Watchdog"
|
|
depends on ISA
|
|
help
|
|
This is a driver for the Mixcom hardware watchdog cards. This
|
|
watchdog simply watches your kernel to make sure it doesn't freeze,
|
|
and if it does, it reboots your computer after a certain amount of
|
|
time.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called mixcomwd.
|
|
|
|
Most people will say N.
|
|
|
|
config WDT
|
|
tristate "WDT Watchdog timer"
|
|
depends on ISA
|
|
help
|
|
If you have a WDT500P or WDT501P watchdog board, say Y here,
|
|
otherwise N. It is not possible to probe for this board, which means
|
|
that you have to inform the kernel about the IO port and IRQ that
|
|
is needed (you can do this via the io and irq parameters)
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called wdt.
|
|
|
|
#
|
|
# PCI-based Watchdog Cards
|
|
#
|
|
|
|
comment "PCI-based Watchdog Cards"
|
|
depends on PCI
|
|
|
|
config PCIPCWATCHDOG
|
|
tristate "Berkshire Products PCI-PC Watchdog"
|
|
depends on PCI
|
|
help
|
|
This is the driver for the Berkshire Products PCI-PC Watchdog card.
|
|
This card simply watches your kernel to make sure it doesn't freeze,
|
|
and if it does, it reboots your computer after a certain amount of
|
|
time. The card can also monitor the internal temperature of the PC.
|
|
More info is available at <http://www.berkprod.com/pci_pc_watchdog.htm>.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called pcwd_pci.
|
|
|
|
Most people will say N.
|
|
|
|
config WDTPCI
|
|
tristate "PCI-WDT500/501 Watchdog timer"
|
|
depends on PCI
|
|
help
|
|
If you have a PCI-WDT500/501 watchdog board, say Y here, otherwise N.
|
|
|
|
If you have a PCI-WDT501 watchdog board then you can enable the
|
|
temperature sensor by setting the type parameter to 501.
|
|
|
|
If you want to enable the Fan Tachometer on the PCI-WDT501, then you
|
|
can do this via the tachometer parameter. Only do this if you have a
|
|
fan tachometer actually set up.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called wdt_pci.
|
|
|
|
#
|
|
# USB-based Watchdog Cards
|
|
#
|
|
|
|
comment "USB-based Watchdog Cards"
|
|
depends on USB
|
|
|
|
config USBPCWATCHDOG
|
|
tristate "Berkshire Products USB-PC Watchdog"
|
|
depends on USB
|
|
help
|
|
This is the driver for the Berkshire Products USB-PC Watchdog card.
|
|
This card simply watches your kernel to make sure it doesn't freeze,
|
|
and if it does, it reboots your computer after a certain amount of
|
|
time. The card can also monitor the internal temperature of the PC.
|
|
More info is available at <http://www.berkprod.com/usb_pc_watchdog.htm>.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called pcwd_usb.
|
|
|
|
Most people will say N.
|
|
|
|
config KEEMBAY_WATCHDOG
|
|
tristate "Intel Keem Bay SoC non-secure watchdog"
|
|
depends on ARCH_KEEMBAY || (ARM64 && COMPILE_TEST)
|
|
select WATCHDOG_CORE
|
|
help
|
|
This option enable support for an In-secure watchdog timer driver for
|
|
Intel Keem Bay SoC. This WDT has a 32 bit timer and decrements in every
|
|
count unit. An interrupt will be triggered, when the count crosses
|
|
the threshold configured in the register.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called keembay_wdt.
|
|
|
|
endif # WATCHDOG
|