349 lines
8.2 KiB
C
349 lines
8.2 KiB
C
// SPDX-License-Identifier: GPL-2.0-only
|
|
|
|
/*
|
|
* aht10.c - Linux hwmon driver for AHT10 Temperature and Humidity sensor
|
|
* Copyright (C) 2020 Johannes Cornelis Draaijer
|
|
*/
|
|
|
|
#include <linux/delay.h>
|
|
#include <linux/hwmon.h>
|
|
#include <linux/i2c.h>
|
|
#include <linux/ktime.h>
|
|
#include <linux/module.h>
|
|
|
|
#define AHT10_MEAS_SIZE 6
|
|
|
|
/*
|
|
* Poll intervals (in milliseconds)
|
|
*/
|
|
#define AHT10_DEFAULT_MIN_POLL_INTERVAL 2000
|
|
#define AHT10_MIN_POLL_INTERVAL 2000
|
|
|
|
/*
|
|
* I2C command delays (in microseconds)
|
|
*/
|
|
#define AHT10_MEAS_DELAY 80000
|
|
#define AHT10_CMD_DELAY 350000
|
|
#define AHT10_DELAY_EXTRA 100000
|
|
|
|
/*
|
|
* Command bytes
|
|
*/
|
|
#define AHT10_CMD_INIT 0b11100001
|
|
#define AHT10_CMD_MEAS 0b10101100
|
|
#define AHT10_CMD_RST 0b10111010
|
|
|
|
/*
|
|
* Flags in the answer byte/command
|
|
*/
|
|
#define AHT10_CAL_ENABLED BIT(3)
|
|
#define AHT10_BUSY BIT(7)
|
|
#define AHT10_MODE_NOR (BIT(5) | BIT(6))
|
|
#define AHT10_MODE_CYC BIT(5)
|
|
#define AHT10_MODE_CMD BIT(6)
|
|
|
|
#define AHT10_MAX_POLL_INTERVAL_LEN 30
|
|
|
|
/**
|
|
* struct aht10_data - All the data required to operate an AHT10 chip
|
|
* @client: the i2c client associated with the AHT10
|
|
* @lock: a mutex that is used to prevent parallel access to the
|
|
* i2c client
|
|
* @min_poll_interval: the minimum poll interval
|
|
* While the poll rate limit is not 100% necessary,
|
|
* the datasheet recommends that a measurement
|
|
* is not performed too often to prevent
|
|
* the chip from warming up due to the heat it generates.
|
|
* If it's unwanted, it can be ignored setting it to
|
|
* it to 0. Default value is 2000 ms
|
|
* @previous_poll_time: the previous time that the AHT10
|
|
* was polled
|
|
* @temperature: the latest temperature value received from
|
|
* the AHT10
|
|
* @humidity: the latest humidity value received from the
|
|
* AHT10
|
|
*/
|
|
|
|
struct aht10_data {
|
|
struct i2c_client *client;
|
|
/*
|
|
* Prevent simultaneous access to the i2c
|
|
* client and previous_poll_time
|
|
*/
|
|
struct mutex lock;
|
|
ktime_t min_poll_interval;
|
|
ktime_t previous_poll_time;
|
|
int temperature;
|
|
int humidity;
|
|
};
|
|
|
|
/**
|
|
* aht10_init() - Initialize an AHT10 chip
|
|
* @client: the i2c client associated with the AHT10
|
|
* @data: the data associated with this AHT10 chip
|
|
* Return: 0 if succesfull, 1 if not
|
|
*/
|
|
static int aht10_init(struct aht10_data *data)
|
|
{
|
|
const u8 cmd_init[] = {AHT10_CMD_INIT, AHT10_CAL_ENABLED | AHT10_MODE_CYC,
|
|
0x00};
|
|
int res;
|
|
u8 status;
|
|
struct i2c_client *client = data->client;
|
|
|
|
res = i2c_master_send(client, cmd_init, 3);
|
|
if (res < 0)
|
|
return res;
|
|
|
|
usleep_range(AHT10_CMD_DELAY, AHT10_CMD_DELAY +
|
|
AHT10_DELAY_EXTRA);
|
|
|
|
res = i2c_master_recv(client, &status, 1);
|
|
if (res != 1)
|
|
return -ENODATA;
|
|
|
|
if (status & AHT10_BUSY)
|
|
return -EBUSY;
|
|
|
|
return 0;
|
|
}
|
|
|
|
/**
|
|
* aht10_polltime_expired() - check if the minimum poll interval has
|
|
* expired
|
|
* @data: the data containing the time to compare
|
|
* Return: 1 if the minimum poll interval has expired, 0 if not
|
|
*/
|
|
static int aht10_polltime_expired(struct aht10_data *data)
|
|
{
|
|
ktime_t current_time = ktime_get_boottime();
|
|
ktime_t difference = ktime_sub(current_time, data->previous_poll_time);
|
|
|
|
return ktime_after(difference, data->min_poll_interval);
|
|
}
|
|
|
|
/**
|
|
* aht10_read_values() - read and parse the raw data from the AHT10
|
|
* @aht10_data: the struct aht10_data to use for the lock
|
|
* Return: 0 if succesfull, 1 if not
|
|
*/
|
|
static int aht10_read_values(struct aht10_data *data)
|
|
{
|
|
const u8 cmd_meas[] = {AHT10_CMD_MEAS, 0x33, 0x00};
|
|
u32 temp, hum;
|
|
int res;
|
|
u8 raw_data[AHT10_MEAS_SIZE];
|
|
struct i2c_client *client = data->client;
|
|
|
|
mutex_lock(&data->lock);
|
|
if (aht10_polltime_expired(data)) {
|
|
res = i2c_master_send(client, cmd_meas, sizeof(cmd_meas));
|
|
if (res < 0) {
|
|
mutex_unlock(&data->lock);
|
|
return res;
|
|
}
|
|
|
|
usleep_range(AHT10_MEAS_DELAY,
|
|
AHT10_MEAS_DELAY + AHT10_DELAY_EXTRA);
|
|
|
|
res = i2c_master_recv(client, raw_data, AHT10_MEAS_SIZE);
|
|
if (res != AHT10_MEAS_SIZE) {
|
|
mutex_unlock(&data->lock);
|
|
if (res >= 0)
|
|
return -ENODATA;
|
|
else
|
|
return res;
|
|
}
|
|
|
|
hum = ((u32)raw_data[1] << 12u) |
|
|
((u32)raw_data[2] << 4u) |
|
|
((raw_data[3] & 0xF0u) >> 4u);
|
|
|
|
temp = ((u32)(raw_data[3] & 0x0Fu) << 16u) |
|
|
((u32)raw_data[4] << 8u) |
|
|
raw_data[5];
|
|
|
|
temp = ((temp * 625) >> 15u) * 10;
|
|
hum = ((hum * 625) >> 16u) * 10;
|
|
|
|
data->temperature = (int)temp - 50000;
|
|
data->humidity = hum;
|
|
data->previous_poll_time = ktime_get_boottime();
|
|
}
|
|
mutex_unlock(&data->lock);
|
|
return 0;
|
|
}
|
|
|
|
/**
|
|
* aht10_interval_write() - store the given minimum poll interval.
|
|
* Return: 0 on success, -EINVAL if a value lower than the
|
|
* AHT10_MIN_POLL_INTERVAL is given
|
|
*/
|
|
static ssize_t aht10_interval_write(struct aht10_data *data,
|
|
long val)
|
|
{
|
|
data->min_poll_interval = ms_to_ktime(clamp_val(val, 2000, LONG_MAX));
|
|
return 0;
|
|
}
|
|
|
|
/**
|
|
* aht10_interval_read() - read the minimum poll interval
|
|
* in milliseconds
|
|
*/
|
|
static ssize_t aht10_interval_read(struct aht10_data *data,
|
|
long *val)
|
|
{
|
|
*val = ktime_to_ms(data->min_poll_interval);
|
|
return 0;
|
|
}
|
|
|
|
/**
|
|
* aht10_temperature1_read() - read the temperature in millidegrees
|
|
*/
|
|
static int aht10_temperature1_read(struct aht10_data *data, long *val)
|
|
{
|
|
int res;
|
|
|
|
res = aht10_read_values(data);
|
|
if (res < 0)
|
|
return res;
|
|
|
|
*val = data->temperature;
|
|
return 0;
|
|
}
|
|
|
|
/**
|
|
* aht10_humidity1_read() - read the relative humidity in millipercent
|
|
*/
|
|
static int aht10_humidity1_read(struct aht10_data *data, long *val)
|
|
{
|
|
int res;
|
|
|
|
res = aht10_read_values(data);
|
|
if (res < 0)
|
|
return res;
|
|
|
|
*val = data->humidity;
|
|
return 0;
|
|
}
|
|
|
|
static umode_t aht10_hwmon_visible(const void *data, enum hwmon_sensor_types type,
|
|
u32 attr, int channel)
|
|
{
|
|
switch (type) {
|
|
case hwmon_temp:
|
|
case hwmon_humidity:
|
|
return 0444;
|
|
case hwmon_chip:
|
|
return 0644;
|
|
default:
|
|
return 0;
|
|
}
|
|
}
|
|
|
|
static int aht10_hwmon_read(struct device *dev, enum hwmon_sensor_types type,
|
|
u32 attr, int channel, long *val)
|
|
{
|
|
struct aht10_data *data = dev_get_drvdata(dev);
|
|
|
|
switch (type) {
|
|
case hwmon_temp:
|
|
return aht10_temperature1_read(data, val);
|
|
case hwmon_humidity:
|
|
return aht10_humidity1_read(data, val);
|
|
case hwmon_chip:
|
|
return aht10_interval_read(data, val);
|
|
default:
|
|
return -EOPNOTSUPP;
|
|
}
|
|
}
|
|
|
|
static int aht10_hwmon_write(struct device *dev, enum hwmon_sensor_types type,
|
|
u32 attr, int channel, long val)
|
|
{
|
|
struct aht10_data *data = dev_get_drvdata(dev);
|
|
|
|
switch (type) {
|
|
case hwmon_chip:
|
|
return aht10_interval_write(data, val);
|
|
default:
|
|
return -EOPNOTSUPP;
|
|
}
|
|
}
|
|
|
|
static const struct hwmon_channel_info *aht10_info[] = {
|
|
HWMON_CHANNEL_INFO(chip, HWMON_C_UPDATE_INTERVAL),
|
|
HWMON_CHANNEL_INFO(temp, HWMON_T_INPUT),
|
|
HWMON_CHANNEL_INFO(humidity, HWMON_H_INPUT),
|
|
NULL,
|
|
};
|
|
|
|
static const struct hwmon_ops aht10_hwmon_ops = {
|
|
.is_visible = aht10_hwmon_visible,
|
|
.read = aht10_hwmon_read,
|
|
.write = aht10_hwmon_write,
|
|
};
|
|
|
|
static const struct hwmon_chip_info aht10_chip_info = {
|
|
.ops = &aht10_hwmon_ops,
|
|
.info = aht10_info,
|
|
};
|
|
|
|
static int aht10_probe(struct i2c_client *client,
|
|
const struct i2c_device_id *aht10_id)
|
|
{
|
|
struct device *device = &client->dev;
|
|
struct device *hwmon_dev;
|
|
struct aht10_data *data;
|
|
int res;
|
|
|
|
if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C))
|
|
return -ENOENT;
|
|
|
|
data = devm_kzalloc(device, sizeof(*data), GFP_KERNEL);
|
|
if (!data)
|
|
return -ENOMEM;
|
|
|
|
data->min_poll_interval = ms_to_ktime(AHT10_DEFAULT_MIN_POLL_INTERVAL);
|
|
data->client = client;
|
|
|
|
mutex_init(&data->lock);
|
|
|
|
res = aht10_init(data);
|
|
if (res < 0)
|
|
return res;
|
|
|
|
res = aht10_read_values(data);
|
|
if (res < 0)
|
|
return res;
|
|
|
|
hwmon_dev = devm_hwmon_device_register_with_info(device,
|
|
client->name,
|
|
data,
|
|
&aht10_chip_info,
|
|
NULL);
|
|
|
|
return PTR_ERR_OR_ZERO(hwmon_dev);
|
|
}
|
|
|
|
static const struct i2c_device_id aht10_id[] = {
|
|
{ "aht10", 0 },
|
|
{ },
|
|
};
|
|
MODULE_DEVICE_TABLE(i2c, aht10_id);
|
|
|
|
static struct i2c_driver aht10_driver = {
|
|
.driver = {
|
|
.name = "aht10",
|
|
},
|
|
.probe = aht10_probe,
|
|
.id_table = aht10_id,
|
|
};
|
|
|
|
module_i2c_driver(aht10_driver);
|
|
|
|
MODULE_AUTHOR("Johannes Cornelis Draaijer <jcdra1@gmail.com>");
|
|
MODULE_DESCRIPTION("AHT10 Temperature and Humidity sensor driver");
|
|
MODULE_VERSION("1.0");
|
|
MODULE_LICENSE("GPL v2");
|