77 lines
2.9 KiB
Plaintext
77 lines
2.9 KiB
Plaintext
|
* AMD 10GbE driver (amd-xgbe)
|
||
|
|
|
||
|
|
Required properties:
|
||
|
|
- compatible: Should be "amd,xgbe-seattle-v1a"
|
||
|
|
- reg: Address and length of the register sets for the device
|
||
|
|
- MAC registers
|
||
|
|
- PCS registers
|
||
|
|
- SerDes Rx/Tx registers
|
||
|
|
- SerDes integration registers (1/2)
|
||
|
|
- SerDes integration registers (2/2)
|
||
|
|
- interrupts: Should contain the amd-xgbe interrupt(s). The first interrupt
|
||
|
|
listed is required and is the general device interrupt. If the optional
|
||
|
|
amd,per-channel-interrupt property is specified, then one additional
|
||
|
|
interrupt for each DMA channel supported by the device should be specified.
|
||
|
|
The last interrupt listed should be the PCS auto-negotiation interrupt.
|
||
|
|
- clocks:
|
||
|
|
- DMA clock for the amd-xgbe device (used for calculating the
|
||
|
|
correct Rx interrupt watchdog timer value on a DMA channel
|
||
|
|
for coalescing)
|
||
|
|
- PTP clock for the amd-xgbe device
|
||
|
|
- clock-names: Should be the names of the clocks
|
||
|
|
- "dma_clk" for the DMA clock
|
||
|
|
- "ptp_clk" for the PTP clock
|
||
|
|
- phy-mode: See ethernet.txt file in the same directory
|
||
|
|
|
||
|
|
Optional properties:
|
||
|
|
- dma-coherent: Present if dma operations are coherent
|
||
|
|
- amd,per-channel-interrupt: Indicates that Rx and Tx complete will generate
|
||
|
|
a unique interrupt for each DMA channel - this requires an additional
|
||
|
|
interrupt be configured for each DMA channel
|
||
|
|
- amd,speed-set: Speed capabilities of the device
|
||
|
|
0 - 1GbE and 10GbE (default)
|
||
|
|
1 - 2.5GbE and 10GbE
|
||
|
|
|
||
|
|
The MAC address will be determined using the optional properties defined in
|
||
|
|
ethernet.txt.
|
||
|
|
|
||
|
|
The following optional properties are represented by an array with each
|
||
|
|
value corresponding to a particular speed. The first array value represents
|
||
|
|
the setting for the 1GbE speed, the second value for the 2.5GbE speed and
|
||
|
|
the third value for the 10GbE speed. All three values are required if the
|
||
|
|
property is used.
|
||
|
|
- amd,serdes-blwc: Baseline wandering correction enablement
|
||
|
|
0 - Off
|
||
|
|
1 - On
|
||
|
|
- amd,serdes-cdr-rate: CDR rate speed selection
|
||
|
|
- amd,serdes-pq-skew: PQ (data sampling) skew
|
||
|
|
- amd,serdes-tx-amp: TX amplitude boost
|
||
|
|
- amd,serdes-dfe-tap-config: DFE taps available to run
|
||
|
|
- amd,serdes-dfe-tap-enable: DFE taps to enable
|
||
|
|
|
||
|
|
Example:
|
||
|
|
xgbe@e0700000 {
|
||
|
|
compatible = "amd,xgbe-seattle-v1a";
|
||
|
|
reg = <0 0xe0700000 0 0x80000>,
|
||
|
|
<0 0xe0780000 0 0x80000>,
|
||
|
|
<0 0xe1240800 0 0x00400>,
|
||
|
|
<0 0xe1250000 0 0x00060>,
|
||
|
|
<0 0xe1250080 0 0x00004>;
|
||
|
|
interrupt-parent = <&gic>;
|
||
|
|
interrupts = <0 325 4>,
|
||
|
|
<0 326 1>, <0 327 1>, <0 328 1>, <0 329 1>,
|
||
|
|
<0 323 4>;
|
||
|
|
amd,per-channel-interrupt;
|
||
|
|
clocks = <&xgbe_dma_clk>, <&xgbe_ptp_clk>;
|
||
|
|
clock-names = "dma_clk", "ptp_clk";
|
||
|
|
phy-mode = "xgmii";
|
||
|
|
mac-address = [ 02 a1 a2 a3 a4 a5 ];
|
||
|
|
amd,speed-set = <0>;
|
||
|
|
amd,serdes-blwc = <1>, <1>, <0>;
|
||
|
|
amd,serdes-cdr-rate = <2>, <2>, <7>;
|
||
|
|
amd,serdes-pq-skew = <10>, <10>, <30>;
|
||
|
|
amd,serdes-tx-amp = <15>, <15>, <10>;
|
||
|
|
amd,serdes-dfe-tap-config = <3>, <3>, <1>;
|
||
|
|
amd,serdes-dfe-tap-enable = <0>, <0>, <127>;
|
||
|
|
};
|