59 lines
2.2 KiB
Plaintext
59 lines
2.2 KiB
Plaintext
|
* Samsung's I2C controller
|
||
|
|
|
||
|
|
The Samsung's I2C controller is used to interface with I2C devices.
|
||
|
|
|
||
|
|
Required properties:
|
||
|
|
- compatible: value should be either of the following.
|
||
|
|
(a) "samsung, s3c2410-i2c", for i2c compatible with s3c2410 i2c.
|
||
|
|
(b) "samsung, s3c2440-i2c", for i2c compatible with s3c2440 i2c.
|
||
|
|
(c) "samsung, s3c2440-hdmiphy-i2c", for s3c2440-like i2c used
|
||
|
|
inside HDMIPHY block found on several samsung SoCs
|
||
|
|
(d) "samsung, exynos5-sata-phy-i2c", for s3c2440-like i2c used as
|
||
|
|
a host to SATA PHY controller on an internal bus.
|
||
|
|
- reg: physical base address of the controller and length of memory mapped
|
||
|
|
region.
|
||
|
|
- interrupts: interrupt number to the cpu.
|
||
|
|
- samsung,i2c-sda-delay: Delay (in ns) applied to data line (SDA) edges.
|
||
|
|
|
||
|
|
Required for all cases except "samsung,s3c2440-hdmiphy-i2c":
|
||
|
|
- Samsung GPIO variant (deprecated):
|
||
|
|
- gpios: The order of the gpios should be the following: <SDA, SCL>.
|
||
|
|
The gpio specifier depends on the gpio controller. Required in all
|
||
|
|
cases except for "samsung,s3c2440-hdmiphy-i2c" whose input/output
|
||
|
|
lines are permanently wired to the respective clienta
|
||
|
|
- Pinctrl variant (preferred, if available):
|
||
|
|
- pinctrl-0: Pin control group to be used for this controller.
|
||
|
|
- pinctrl-names: Should contain only one value - "default".
|
||
|
|
|
||
|
|
Optional properties:
|
||
|
|
- samsung,i2c-slave-addr: Slave address in multi-master environment. If not
|
||
|
|
specified, default value is 0.
|
||
|
|
- samsung,i2c-max-bus-freq: Desired frequency in Hz of the bus. If not
|
||
|
|
specified, the default value in Hz is 100000.
|
||
|
|
- samsung,sysreg-phandle - handle to syscon used to control the system registers
|
||
|
|
|
||
|
|
Example:
|
||
|
|
|
||
|
|
i2c@13870000 {
|
||
|
|
compatible = "samsung,s3c2440-i2c";
|
||
|
|
reg = <0x13870000 0x100>;
|
||
|
|
interrupts = <345>;
|
||
|
|
samsung,i2c-sda-delay = <100>;
|
||
|
|
samsung,i2c-max-bus-freq = <100000>;
|
||
|
|
/* Samsung GPIO variant begins here */
|
||
|
|
gpios = <&gpd1 2 0 /* SDA */
|
||
|
|
&gpd1 3 0 /* SCL */>;
|
||
|
|
/* Samsung GPIO variant ends here */
|
||
|
|
/* Pinctrl variant begins here */
|
||
|
|
pinctrl-0 = <&i2c3_bus>;
|
||
|
|
pinctrl-names = "default";
|
||
|
|
/* Pinctrl variant ends here */
|
||
|
|
#address-cells = <1>;
|
||
|
|
#size-cells = <0>;
|
||
|
|
|
||
|
|
wm8994@1a {
|
||
|
|
compatible = "wlf,wm8994";
|
||
|
|
reg = <0x1a>;
|
||
|
|
};
|
||
|
|
};
|