211 lines
7.2 KiB
YAML
211 lines
7.2 KiB
YAML
|
# SPDX-License-Identifier: (GPL-2.0+ OR BSD-2-Clause)
|
|||
|
|
# Copyright (C) 2019 Texas Instruments Incorporated
|
|||
|
|
%YAML 1.2
|
|||
|
|
---
|
|||
|
|
$id: http://devicetree.org/schemas/sound/tlv320adcx140.yaml#
|
|||
|
|
$schema: http://devicetree.org/meta-schemas/core.yaml#
|
|||
|
|
|
|||
|
|
title: Texas Instruments TLV320ADCX140 Quad Channel Analog-to-Digital Converter
|
|||
|
|
|
|||
|
|
maintainers:
|
|||
|
|
- Dan Murphy <dmurphy@ti.com>
|
|||
|
|
|
|||
|
|
description: |
|
|||
|
|
The TLV320ADCX140 are multichannel (4-ch analog recording or 8-ch digital
|
|||
|
|
PDM microphones recording), high-performance audio, analog-to-digital
|
|||
|
|
converter (ADC) with analog inputs supporting up to 2V RMS. The TLV320ADCX140
|
|||
|
|
family supports line and microphone Inputs, and offers a programmable
|
|||
|
|
microphone bias or supply voltage generation.
|
|||
|
|
|
|||
|
|
Specifications can be found at:
|
|||
|
|
https://www.ti.com/lit/ds/symlink/tlv320adc3140.pdf
|
|||
|
|
https://www.ti.com/lit/ds/symlink/tlv320adc5140.pdf
|
|||
|
|
https://www.ti.com/lit/ds/symlink/tlv320adc6140.pdf
|
|||
|
|
|
|||
|
|
properties:
|
|||
|
|
compatible:
|
|||
|
|
enum:
|
|||
|
|
- ti,tlv320adc3140
|
|||
|
|
- ti,tlv320adc5140
|
|||
|
|
- ti,tlv320adc6140
|
|||
|
|
|
|||
|
|
reg:
|
|||
|
|
maxItems: 1
|
|||
|
|
description: |
|
|||
|
|
I2C addresss of the device can be one of these 0x4c, 0x4d, 0x4e or 0x4f
|
|||
|
|
|
|||
|
|
reset-gpios:
|
|||
|
|
maxItems: 1
|
|||
|
|
description: |
|
|||
|
|
GPIO used for hardware reset.
|
|||
|
|
|
|||
|
|
areg-supply:
|
|||
|
|
description: |
|
|||
|
|
Regulator with AVDD at 3.3V. If not defined then the internal regulator
|
|||
|
|
is enabled.
|
|||
|
|
|
|||
|
|
ti,mic-bias-source:
|
|||
|
|
description: |
|
|||
|
|
Indicates the source for MIC Bias.
|
|||
|
|
0 - Mic bias is set to VREF
|
|||
|
|
1 - Mic bias is set to VREF × 1.096
|
|||
|
|
6 - Mic bias is set to AVDD
|
|||
|
|
$ref: /schemas/types.yaml#/definitions/uint32
|
|||
|
|
enum: [0, 1, 6]
|
|||
|
|
|
|||
|
|
ti,vref-source:
|
|||
|
|
description: |
|
|||
|
|
Indicates the source for MIC Bias.
|
|||
|
|
0 - Set VREF to 2.75V
|
|||
|
|
1 - Set VREF to 2.5V
|
|||
|
|
2 - Set VREF to 1.375V
|
|||
|
|
$ref: /schemas/types.yaml#/definitions/uint32
|
|||
|
|
enum: [0, 1, 2]
|
|||
|
|
|
|||
|
|
ti,pdm-edge-select:
|
|||
|
|
description: |
|
|||
|
|
Defines the PDMCLK sampling edge configuration for the PDM inputs. This
|
|||
|
|
array is defined as <PDMIN1 PDMIN2 PDMIN3 PDMIN4>.
|
|||
|
|
|
|||
|
|
0 - (default) Odd channel is latched on the negative edge and even
|
|||
|
|
channel is latched on the the positive edge.
|
|||
|
|
1 - Odd channel is latched on the positive edge and even channel is
|
|||
|
|
latched on the the negative edge.
|
|||
|
|
|
|||
|
|
PDMIN1 - PDMCLK latching edge used for channel 1 and 2 data
|
|||
|
|
PDMIN2 - PDMCLK latching edge used for channel 3 and 4 data
|
|||
|
|
PDMIN3 - PDMCLK latching edge used for channel 5 and 6 data
|
|||
|
|
PDMIN4 - PDMCLK latching edge used for channel 7 and 8 data
|
|||
|
|
|
|||
|
|
$ref: /schemas/types.yaml#/definitions/uint32-array
|
|||
|
|
minItems: 1
|
|||
|
|
maxItems: 4
|
|||
|
|
items:
|
|||
|
|
maximum: 1
|
|||
|
|
default: [0, 0, 0, 0]
|
|||
|
|
|
|||
|
|
ti,gpi-config:
|
|||
|
|
description: |
|
|||
|
|
Defines the configuration for the general purpose input pins (GPI).
|
|||
|
|
The array is defined as <GPI1 GPI2 GPI3 GPI4>.
|
|||
|
|
|
|||
|
|
0 - (default) disabled
|
|||
|
|
1 - GPIX is configured as a general-purpose input (GPI)
|
|||
|
|
2 - GPIX is configured as a master clock input (MCLK)
|
|||
|
|
3 - GPIX is configured as an ASI input for daisy-chain (SDIN)
|
|||
|
|
4 - GPIX is configured as a PDM data input for channel 1 and channel
|
|||
|
|
(PDMDIN1)
|
|||
|
|
5 - GPIX is configured as a PDM data input for channel 3 and channel
|
|||
|
|
(PDMDIN2)
|
|||
|
|
6 - GPIX is configured as a PDM data input for channel 5 and channel
|
|||
|
|
(PDMDIN3)
|
|||
|
|
7 - GPIX is configured as a PDM data input for channel 7 and channel
|
|||
|
|
(PDMDIN4)
|
|||
|
|
|
|||
|
|
$ref: /schemas/types.yaml#/definitions/uint32-array
|
|||
|
|
minItems: 1
|
|||
|
|
maxItems: 4
|
|||
|
|
items:
|
|||
|
|
maximum: 7
|
|||
|
|
default: [0, 0, 0, 0]
|
|||
|
|
|
|||
|
|
ti,asi-tx-drive:
|
|||
|
|
type: boolean
|
|||
|
|
description: |
|
|||
|
|
When set the device will set the Tx ASI output to a Hi-Z state for unused
|
|||
|
|
data cycles. Default is to drive the output low on unused ASI cycles.
|
|||
|
|
|
|||
|
|
patternProperties:
|
|||
|
|
'^ti,gpo-config-[1-4]$':
|
|||
|
|
$ref: /schemas/types.yaml#/definitions/uint32-array
|
|||
|
|
description: |
|
|||
|
|
Defines the configuration and output driver for the general purpose
|
|||
|
|
output pins (GPO). These values are pairs, the first value is for the
|
|||
|
|
configuration type and the second value is for the output drive type.
|
|||
|
|
The array is defined as <GPO_CFG GPO_DRV>
|
|||
|
|
|
|||
|
|
GPO output configuration can be one of the following:
|
|||
|
|
|
|||
|
|
0 - (default) disabled
|
|||
|
|
1 - GPOX is configured as a general-purpose output (GPO)
|
|||
|
|
2 - GPOX is configured as a device interrupt output (IRQ)
|
|||
|
|
3 - GPOX is configured as a secondary ASI output (SDOUT2)
|
|||
|
|
4 - GPOX is configured as a PDM clock output (PDMCLK)
|
|||
|
|
|
|||
|
|
GPO output drive configuration for the GPO pins can be one of the following:
|
|||
|
|
|
|||
|
|
0d - (default) Hi-Z output
|
|||
|
|
1d - Drive active low and active high
|
|||
|
|
2d - Drive active low and weak high
|
|||
|
|
3d - Drive active low and Hi-Z
|
|||
|
|
4d - Drive weak low and active high
|
|||
|
|
5d - Drive Hi-Z and active high
|
|||
|
|
|
|||
|
|
ti,gpio-config:
|
|||
|
|
description: |
|
|||
|
|
Defines the configuration and output drive for the General Purpose
|
|||
|
|
Input and Output pin (GPIO1). Its value is a pair, the first value is for
|
|||
|
|
the configuration type and the second value is for the output drive
|
|||
|
|
type. The array is defined as <GPIO1_CFG GPIO1_DRV>
|
|||
|
|
|
|||
|
|
configuration for the GPIO pin can be one of the following:
|
|||
|
|
0 - disabled
|
|||
|
|
1 - GPIO1 is configured as a general-purpose output (GPO)
|
|||
|
|
2 - (default) GPIO1 is configured as a device interrupt output (IRQ)
|
|||
|
|
3 - GPIO1 is configured as a secondary ASI output (SDOUT2)
|
|||
|
|
4 - GPIO1 is configured as a PDM clock output (PDMCLK)
|
|||
|
|
8 - GPIO1 is configured as an input to control when MICBIAS turns on or
|
|||
|
|
off (MICBIAS_EN)
|
|||
|
|
9 - GPIO1 is configured as a general-purpose input (GPI)
|
|||
|
|
10 - GPIO1 is configured as a master clock input (MCLK)
|
|||
|
|
11 - GPIO1 is configured as an ASI input for daisy-chain (SDIN)
|
|||
|
|
12 - GPIO1 is configured as a PDM data input for channel 1 and channel 2
|
|||
|
|
(PDMDIN1)
|
|||
|
|
13 - GPIO1 is configured as a PDM data input for channel 3 and channel 4
|
|||
|
|
(PDMDIN2)
|
|||
|
|
14 - GPIO1 is configured as a PDM data input for channel 5 and channel 6
|
|||
|
|
(PDMDIN3)
|
|||
|
|
15 - GPIO1 is configured as a PDM data input for channel 7 and channel 8
|
|||
|
|
(PDMDIN4)
|
|||
|
|
|
|||
|
|
output drive type for the GPIO pin can be one of the following:
|
|||
|
|
0 - Hi-Z output
|
|||
|
|
1 - Drive active low and active high
|
|||
|
|
2 - (default) Drive active low and weak high
|
|||
|
|
3 - Drive active low and Hi-Z
|
|||
|
|
4 - Drive weak low and active high
|
|||
|
|
5 - Drive Hi-Z and active high
|
|||
|
|
|
|||
|
|
allOf:
|
|||
|
|
- $ref: /schemas/types.yaml#/definitions/uint32-array
|
|||
|
|
- minItems: 2
|
|||
|
|
maxItems: 2
|
|||
|
|
items:
|
|||
|
|
maximum: 15
|
|||
|
|
default: [2, 2]
|
|||
|
|
|
|||
|
|
required:
|
|||
|
|
- compatible
|
|||
|
|
- reg
|
|||
|
|
|
|||
|
|
additionalProperties: false
|
|||
|
|
|
|||
|
|
examples:
|
|||
|
|
- |
|
|||
|
|
#include <dt-bindings/gpio/gpio.h>
|
|||
|
|
i2c0 {
|
|||
|
|
#address-cells = <1>;
|
|||
|
|
#size-cells = <0>;
|
|||
|
|
codec: codec@4c {
|
|||
|
|
compatible = "ti,tlv320adc5140";
|
|||
|
|
reg = <0x4c>;
|
|||
|
|
ti,mic-bias-source = <6>;
|
|||
|
|
ti,pdm-edge-select = <0 1 0 1>;
|
|||
|
|
ti,gpi-config = <4 5 6 7>;
|
|||
|
|
ti,gpio-config = <10 2>;
|
|||
|
|
ti,gpo-config-1 = <0 0>;
|
|||
|
|
ti,gpo-config-2 = <0 0>;
|
|||
|
|
reset-gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>;
|
|||
|
|
};
|
|||
|
|
};
|