64 lines
1.3 KiB
Plaintext
64 lines
1.3 KiB
Plaintext
|
RT5651 audio CODEC
|
||
|
|
|
||
|
|
This device supports I2C only.
|
||
|
|
|
||
|
|
Required properties:
|
||
|
|
|
||
|
|
- compatible : "realtek,rt5651".
|
||
|
|
|
||
|
|
- reg : The I2C address of the device.
|
||
|
|
|
||
|
|
Optional properties:
|
||
|
|
|
||
|
|
- realtek,in2-differential
|
||
|
|
Boolean. Indicate MIC2 input are differential, rather than single-ended.
|
||
|
|
|
||
|
|
- realtek,dmic-en
|
||
|
|
Boolean. true if dmic is used.
|
||
|
|
|
||
|
|
- realtek,jack-detect-source
|
||
|
|
u32. Valid values:
|
||
|
|
1: Use JD1_1 pin for jack-detect
|
||
|
|
2: Use JD1_2 pin for jack-detect
|
||
|
|
3: Use JD2 pin for jack-detect
|
||
|
|
|
||
|
|
- realtek,jack-detect-not-inverted
|
||
|
|
bool. Normal jack-detect switches give an inverted (active-low) signal,
|
||
|
|
set this bool in the rare case you've a jack-detect switch which is not
|
||
|
|
inverted.
|
||
|
|
|
||
|
|
- realtek,over-current-threshold-microamp
|
||
|
|
u32, micbias over-current detection threshold in µA, valid values are
|
||
|
|
600, 1500 and 2000µA.
|
||
|
|
|
||
|
|
- realtek,over-current-scale-factor
|
||
|
|
u32, micbias over-current detection scale-factor, valid values are:
|
||
|
|
0: Scale current by 0.5
|
||
|
|
1: Scale current by 0.75
|
||
|
|
2: Scale current by 1.0
|
||
|
|
3: Scale current by 1.5
|
||
|
|
|
||
|
|
Pins on the device (for linking into audio routes) for RT5651:
|
||
|
|
|
||
|
|
* DMIC L1
|
||
|
|
* DMIC R1
|
||
|
|
* IN1P
|
||
|
|
* IN2P
|
||
|
|
* IN2N
|
||
|
|
* IN3P
|
||
|
|
* HPOL
|
||
|
|
* HPOR
|
||
|
|
* LOUTL
|
||
|
|
* LOUTR
|
||
|
|
* PDML
|
||
|
|
* PDMR
|
||
|
|
|
||
|
|
Example:
|
||
|
|
|
||
|
|
rt5651: codec@1a {
|
||
|
|
compatible = "realtek,rt5651";
|
||
|
|
reg = <0x1a>;
|
||
|
|
realtek,dmic-en = "true";
|
||
|
|
realtek,in2-diff = "false";
|
||
|
|
};
|