98 lines
3.1 KiB
Plaintext
98 lines
3.1 KiB
Plaintext
|
Samsung S5C73M3 8Mp camera ISP
|
||
|
|
------------------------------
|
||
|
|
|
||
|
|
The S5C73M3 camera ISP supports MIPI CSI-2 and parallel (ITU-R BT.656) video
|
||
|
|
data busses. The I2C bus is the main control bus and additionally the SPI bus
|
||
|
|
is used, mostly for transferring the firmware to and from the device. Two
|
||
|
|
slave device nodes corresponding to these control bus interfaces are required
|
||
|
|
and should be placed under respective bus controller nodes.
|
||
|
|
|
||
|
|
I2C slave device node
|
||
|
|
---------------------
|
||
|
|
|
||
|
|
Required properties:
|
||
|
|
|
||
|
|
- compatible : "samsung,s5c73m3";
|
||
|
|
- reg : I2C slave address of the sensor;
|
||
|
|
- vdd-int-supply : digital power supply (1.2V);
|
||
|
|
- vdda-supply : analog power supply (1.2V);
|
||
|
|
- vdd-reg-supply : regulator input power supply (2.8V);
|
||
|
|
- vddio-host-supply : host I/O power supply (1.8V to 2.8V);
|
||
|
|
- vddio-cis-supply : CIS I/O power supply (1.2V to 1.8V);
|
||
|
|
- vdd-af-supply : lens power supply (2.8V);
|
||
|
|
- xshutdown-gpios : specifier of GPIO connected to the XSHUTDOWN pin;
|
||
|
|
- standby-gpios : specifier of GPIO connected to the STANDBY pin;
|
||
|
|
- clocks : should contain list of phandle and clock specifier pairs
|
||
|
|
according to common clock bindings for the clocks described
|
||
|
|
in the clock-names property;
|
||
|
|
- clock-names : should contain "cis_extclk" entry for the CIS_EXTCLK clock;
|
||
|
|
|
||
|
|
Optional properties:
|
||
|
|
|
||
|
|
- clock-frequency : the frequency at which the "cis_extclk" clock should be
|
||
|
|
configured to operate, in Hz; if this property is not
|
||
|
|
specified default 24 MHz value will be used.
|
||
|
|
|
||
|
|
The common video interfaces bindings (see video-interfaces.txt) should be used
|
||
|
|
to specify link from the S5C73M3 to an external image data receiver. The S5C73M3
|
||
|
|
device node should contain one 'port' child node with an 'endpoint' subnode for
|
||
|
|
this purpose. The data link from a raw image sensor to the S5C73M3 can be
|
||
|
|
similarly specified, but it is optional since the S5C73M3 ISP and a raw image
|
||
|
|
sensor are usually inseparable and form a hybrid module.
|
||
|
|
|
||
|
|
Following properties are valid for the endpoint node(s):
|
||
|
|
|
||
|
|
endpoint subnode
|
||
|
|
----------------
|
||
|
|
|
||
|
|
- data-lanes : (optional) specifies MIPI CSI-2 data lanes as covered in
|
||
|
|
video-interfaces.txt. This sensor doesn't support data lane remapping
|
||
|
|
and physical lane indexes in subsequent elements of the array should
|
||
|
|
be only consecutive ascending values.
|
||
|
|
|
||
|
|
SPI device node
|
||
|
|
---------------
|
||
|
|
|
||
|
|
Required properties:
|
||
|
|
|
||
|
|
- compatible : "samsung,s5c73m3";
|
||
|
|
|
||
|
|
For more details see description of the SPI busses bindings
|
||
|
|
(../spi/spi-bus.txt) and bindings of a specific bus controller.
|
||
|
|
|
||
|
|
Example:
|
||
|
|
|
||
|
|
i2c@138a000000 {
|
||
|
|
...
|
||
|
|
s5c73m3@3c {
|
||
|
|
compatible = "samsung,s5c73m3";
|
||
|
|
reg = <0x3c>;
|
||
|
|
vdd-int-supply = <&buck9_reg>;
|
||
|
|
vdda-supply = <&ldo17_reg>;
|
||
|
|
vdd-reg-supply = <&cam_io_reg>;
|
||
|
|
vddio-host-supply = <&ldo18_reg>;
|
||
|
|
vddio-cis-supply = <&ldo9_reg>;
|
||
|
|
vdd-af-supply = <&cam_af_reg>;
|
||
|
|
clock-frequency = <24000000>;
|
||
|
|
clocks = <&clk 0>;
|
||
|
|
clock-names = "cis_extclk";
|
||
|
|
reset-gpios = <&gpf1 3 1>;
|
||
|
|
standby-gpios = <&gpm0 1 1>;
|
||
|
|
port {
|
||
|
|
s5c73m3_ep: endpoint {
|
||
|
|
remote-endpoint = <&csis0_ep>;
|
||
|
|
data-lanes = <1 2 3 4>;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
spi@1392000 {
|
||
|
|
...
|
||
|
|
s5c73m3_spi: s5c73m3@0 {
|
||
|
|
compatible = "samsung,s5c73m3";
|
||
|
|
reg = <0>;
|
||
|
|
...
|
||
|
|
};
|
||
|
|
};
|