105 lines
3.1 KiB
Plaintext
105 lines
3.1 KiB
Plaintext
|
# SPDX-License-Identifier: GPL-2.0-only
|
||
|
|
#
|
||
|
|
# Counter devices
|
||
|
|
#
|
||
|
|
|
||
|
|
menuconfig COUNTER
|
||
|
|
tristate "Counter support"
|
||
|
|
help
|
||
|
|
This enables counter device support through the Generic Counter
|
||
|
|
interface. You only need to enable this, if you also want to enable
|
||
|
|
one or more of the counter device drivers below.
|
||
|
|
|
||
|
|
if COUNTER
|
||
|
|
|
||
|
|
config 104_QUAD_8
|
||
|
|
tristate "ACCES 104-QUAD-8 driver"
|
||
|
|
depends on PC104 && X86
|
||
|
|
select ISA_BUS_API
|
||
|
|
help
|
||
|
|
Say yes here to build support for the ACCES 104-QUAD-8 quadrature
|
||
|
|
encoder counter/interface device family (104-QUAD-8, 104-QUAD-4).
|
||
|
|
|
||
|
|
A counter's respective error flag may be cleared by performing a write
|
||
|
|
operation on the respective count value attribute. Although the
|
||
|
|
104-QUAD-8 counters have a 25-bit range, only the lower 24 bits may be
|
||
|
|
set, either directly or via the counter's preset attribute. Interrupts
|
||
|
|
are not supported by this driver.
|
||
|
|
|
||
|
|
The base port addresses for the devices may be configured via the base
|
||
|
|
array module parameter.
|
||
|
|
|
||
|
|
config INTERRUPT_CNT
|
||
|
|
tristate "Interrupt counter driver"
|
||
|
|
depends on GPIOLIB
|
||
|
|
help
|
||
|
|
Select this option to enable interrupt counter driver. Any interrupt
|
||
|
|
source can be used by this driver as the event source.
|
||
|
|
|
||
|
|
To compile this driver as a module, choose M here: the
|
||
|
|
module will be called interrupt-cnt.
|
||
|
|
|
||
|
|
config STM32_TIMER_CNT
|
||
|
|
tristate "STM32 Timer encoder counter driver"
|
||
|
|
depends on MFD_STM32_TIMERS || COMPILE_TEST
|
||
|
|
help
|
||
|
|
Select this option to enable STM32 Timer quadrature encoder
|
||
|
|
and counter driver.
|
||
|
|
|
||
|
|
To compile this driver as a module, choose M here: the
|
||
|
|
module will be called stm32-timer-cnt.
|
||
|
|
|
||
|
|
config STM32_LPTIMER_CNT
|
||
|
|
tristate "STM32 LP Timer encoder counter driver"
|
||
|
|
depends on MFD_STM32_LPTIMER || COMPILE_TEST
|
||
|
|
help
|
||
|
|
Select this option to enable STM32 Low-Power Timer quadrature encoder
|
||
|
|
and counter driver.
|
||
|
|
|
||
|
|
To compile this driver as a module, choose M here: the
|
||
|
|
module will be called stm32-lptimer-cnt.
|
||
|
|
|
||
|
|
config TI_EQEP
|
||
|
|
tristate "TI eQEP counter driver"
|
||
|
|
depends on (SOC_AM33XX || COMPILE_TEST)
|
||
|
|
select REGMAP_MMIO
|
||
|
|
help
|
||
|
|
Select this option to enable the Texas Instruments Enhanced Quadrature
|
||
|
|
Encoder Pulse (eQEP) counter driver.
|
||
|
|
|
||
|
|
To compile this driver as a module, choose M here: the module will be
|
||
|
|
called ti-eqep.
|
||
|
|
|
||
|
|
config FTM_QUADDEC
|
||
|
|
tristate "Flex Timer Module Quadrature decoder driver"
|
||
|
|
depends on HAS_IOMEM && OF
|
||
|
|
help
|
||
|
|
Select this option to enable the Flex Timer Quadrature decoder
|
||
|
|
driver.
|
||
|
|
|
||
|
|
To compile this driver as a module, choose M here: the
|
||
|
|
module will be called ftm-quaddec.
|
||
|
|
|
||
|
|
config MICROCHIP_TCB_CAPTURE
|
||
|
|
tristate "Microchip Timer Counter Capture driver"
|
||
|
|
depends on HAS_IOMEM && OF
|
||
|
|
select REGMAP_MMIO
|
||
|
|
help
|
||
|
|
Select this option to enable the Microchip Timer Counter Block
|
||
|
|
capture driver.
|
||
|
|
|
||
|
|
To compile this driver as a module, choose M here: the
|
||
|
|
module will be called microchip-tcb-capture.
|
||
|
|
|
||
|
|
config INTEL_QEP
|
||
|
|
tristate "Intel Quadrature Encoder Peripheral driver"
|
||
|
|
depends on PCI
|
||
|
|
help
|
||
|
|
Select this option to enable the Intel Quadrature Encoder Peripheral
|
||
|
|
driver.
|
||
|
|
|
||
|
|
To compile this driver as a module, choose M here: the module
|
||
|
|
will be called intel-qep.
|
||
|
|
|
||
|
|
endif # COUNTER
|